manualshive.com logo in svg

Asentria Teleboss 850, Руководство пользователя

Поделиться
Скачать
Asentria Teleboss 850 Скачать руководство пользователя страница 26

TeleBoss 850 2.06.280_STD User Manual 

 

Page 20 

 

 
Mode

 toggles between STATIC, DHCP, or VLAN 

– whichever is appropriate for this Ethernet port.  Default setting is 

STATIC. 
 

IP Address

 is the network address assigned to this Ethernet card.  Default setting is 0.0.0.0 

 

Subnet Mask

 sets the network subnet mask provided by the network administrator.  Default setting is 255.255.255.0 

 

Router Address

 sets the router address provided by the network administrator.  Default setting is 0.0.0.0 

 
NAT

 is an ON/OFF toggle to enable Network Address Translation.  Default setting is ON. 

 

VLAN Settings

 displays the following sub-menu where any of six individual VLAN connections can be configured.  

Refer to the 

VLANs

 section in the Features chapter for a detailed explanation of VLANs. 

 

 
TeleBoss 850 - VLAN Settings 
A) VLAN 1 
. . .  
F) VLAN 6 
 
Enter your Selection: a 
 
TeleBoss 850 - VLAN 1 Settings 
A) ID                                   [0] 
B) Priority                             [0] 
C) IP Address                           [0.0.0.0] 
D) Subnet Mask                          [255.255.255.0] 
E) Router Address                       [0.0.0.0] 
 

 

 Note:

 

The T850 does not heed changes to network configurations while you are connected to a command 

processor via Telnet, web interface, or SSH. Changes, including population of the candidate default router set, are 
pended until all network-based command processor sessions have ended.  Open FTP and RTS connections will fail if 
these settings are changed during an open connection. 
 

Name Resolution Settings 

 

 

 

TeleBoss 850 - Name Resolution Settings 
A) DNS Server 1                         [0.0.0.0] 
B) DNS Server 2                         [0.0.0.0] 
C) DNS Mode                             [MANUAL] 
 

 

DNS Server 1

 / 

2

 are the IP addresses of Domain Name Servers that you may want to configure so that you can use 

host names rather than IP addresses in functions where name resolution may be needed, such as; Email server, RTS 
push hosts, action IP settings, network time servers, scripting tcp connections, etc.  Default setting for each DNS 
Server is 0.0.0.0. 
 

DNS Mode

 toggles between MANUAL, ETH1-DHCP, ETH2-DHCP, and DSL.  Default setting is MANUAL. 

Содержание Teleboss 850
































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды