ARM Musca-S1 Скачать руководство пользователя страница 168

Страница: 168 / 194

Table 3-116 SELECTION_CONTROL_REG Register bit assignments

Bits

Name

Function

[31:3]

Reserved.

[2]

CLOCK_PHASE_SHIFTER_BYPASS

QSPI input clock phase shift control:

0b0

: Clock phase shift activated.

0b1

: Clock phase shift is bypassed and clock

delayed is selected from the pad SCLK_OUT.

Reset value

0b0

[1:0]

CLOCK_PHASE_SHIFTER_SELECT

QSPI input clock phase shift control:

0b00

: No phase shift.

0b01

: 90° phase shift.

0b10

: 180° phase shift.

0b11

: 270° phase shift.

Reset value

0b00

BBGEN_CTRL Register

The BBGEN_CTRL Register characteristics are:

Purpose

Controls transistor body-biasing.

Usage constraints

There are no usage constraints.

Memory offset and full register reset value

See

3.11.2 SCC registers summary

on page 3-125

The following table shows the BBGEN_CTRL Register bit assignments.

Table 3-117 BBGEN_CTRL Register bit assignments

Bits

Name

Function

[31:8]

Reserved.

[7:5]

N_CTRL

Select VBBN_OUT range:

0b001

: VBBN_OUT=-0.4V.

0b010

: VBBN_OUT=-0.6V.

0b011

: VBBN_OUT=-0.8V.

0b100

: VBBN_OUT=-1.0V.

0b101

: VBBN_OUT=-1.2V.

0b110

: VBBN_OUT=-1.4V (recommended).

Reset value

0b000

3 Programmers model

3.11 Serial Configuration Control registers

101835_0000_01_en

reserved.

3-168

Non-Confidential

Содержание Musca-S1


































































































































































































Результаты поиска

Содержание Musca-S1

Отзывы:

Похожие инструкции для Musca-S1

Бренды по названию

Популярные бренды

ARM Musca-S1, Техническое справочное руководство

Результаты поиска

Содержание Musca-S1

Отзывы:

Похожие инструкции для Musca-S1

Бренды по названию

Популярные бренды