ARM Musca-S1 Скачать руководство пользователя страница 114

Страница: 114 / 194

Memory offset and full register reset value

See

3.9.1 PVT sensor control registers summary

on page 3-113

The following table shows the CTRL_REF_COUNTER Register bit assignments.

Table 3-52 CTRL_REF_COUNTER Register bit assignments

Bits

Name

Function

[31:19] -

Reserved.

[18]

CLEAR_SAMPLED_VAL

Clear sensors sampled flags:

0b0

: No effect.

0b1

: Clear sensors sampled flags.

Reset value

0b0

[17]

CLEAR_OVERFLOW

Clear sensors overflows:

0b0

: No effect.

0b1

: Clear overflows:

Reset value

0b0

[16]

CLEAR_CNTR

Clear sensors counters:

0b0

: No effect.

0b1

: Clear counters:

Reset value

0b0

[15:4]

Reserved.

[3]

CTRL_IRQ_CLEAR

Clear PVT interrupt:

0b0

: No effect.

0b1

: Clear interrupt:

Reset value

0b0

[2]

CTRL_IRQ_EN

Enable PVT interrupt:

0b0

: No effect.

0b1

: Clear interrupt:

Reset value

0b0

[1]

CTRL_AUTORESTART_EN

Select operating mode of PVT sensors:

0b0

: One-shot mode.

0b1

: Repeat mode:

Reset value

0b0

[0]

CTR_CNTR_EN

Enable reference counter:

0b0

: Not enabled.

0b1

: Enabled:

Reset value

0b0

3 Programmers model

3.9 PVT sensor registers

101835_0000_01_en

reserved.

3-114

Non-Confidential

Содержание Musca-S1


































































































































































































Результаты поиска

Содержание Musca-S1

Отзывы:

Похожие инструкции для Musca-S1

Бренды по названию

Популярные бренды

ARM Musca-S1, Техническое справочное руководство

Результаты поиска

Содержание Musca-S1

Отзывы:

Похожие инструкции для Musca-S1

Бренды по названию

Популярные бренды