ARM Musca-S1 Скачать руководство пользователя страница 123

Страница: 123 / 194

Musca-S1 test chip

SEL

MAIN_OUT[26:0]

ALTF1_OUT[26:0]

SEL

IOMUX_ALTF2_OUTSEL[26:0]

ALTF2_OUT[26:0]

ALTF3_OUT[26:0]

ALTF1_OE[26:0]

SEL

IOMUX_ALTF2_OENSEL[26:0]

ALTF2_OE[26:0]

ALTF3_OE[26:0]

MAIN_IN[26:0]

ALTF1_IN[26:0]

IOMUX_ALTF2_INSEL[26:0]

ALTF2_IN[26:0]

ALTF3_IN[26:0]

PA[26:0]

SEL

IOMUX_MAIN_OUTSEL[26:0]

SEL

IOMUX_MAIN_OENSEL[26:0]

SEL

IOMUX_MAIN_INSEL[26:0]

SEL

IOMUX_ALTF1_OUTSEL[26:0]

MAIN_OE[26:0]

SEL

IOMUX_ALTF1_OENSEL[26:0]

IOMUX_ALTF1_INSEL[26:0]

MAIN multiplexers:

Unselected inputs defined by

IOMUX_MAIN_DEFAULT_IN

registers

ALTF1 multiplexers:

Unselected inputs defined by

IOMUX_ALTF1_DEFAULT_IN

registers

ALTF2 multiplexers:

Unselected inputs defined by

IOMUX_ALTF2_DEFAULT_IN

registers

Figure 3-6 Test chip I/O multiplexer logic

The IOMUX registers control the IOMUX multiplexer logic. The following table shows the IOMUX
registers in offset order from the SCC base memory address of

0x4010_C000

in the Non-secure region, or

0x5010_C000

in the Secure region.

Note

See

3.11.2 SCC registers summary

on page 3-125

for the read/write access characteristics.

3 Programmers model

3.11 Serial Configuration Control registers

101835_0000_01_en

reserved.

3-123

Non-Confidential

Содержание Musca-S1


































































































































































































Результаты поиска

Содержание Musca-S1

Отзывы:

Похожие инструкции для Musca-S1

Бренды по названию

Популярные бренды

ARM Musca-S1, Техническое справочное руководство

Результаты поиска

Содержание Musca-S1

Отзывы:

Похожие инструкции для Musca-S1

Бренды по названию

Популярные бренды