ARM Musca-S1 Скачать руководство пользователя страница 169

Страница: 169 / 194

Table 3-117 BBGEN_CTRL Register bit assignments (continued)

Bits

Name

Function

[4]

BP_HIGH

Bypass AVDD to Positive BBG. To apply
body-biasing in bypass mode, mix settings
with external voltages apply to VBBP and
VBBN pads:

0b0

: Apply VBBP=VDD_CORE, VBBN=0V.

0b1

: Bypass AVDD for enhanced bypass.

Apply VBBP=AVDD, VBBN=0V.

Reset value

0b0

[3:1]

P_CTRL

Select VBBP range:

0b001

: VBBP_OUT=DVDD+0.2V.

0b010

: VBBP_OUT=DVDD+0.3V.

0b011

: VBBP_OUT=DVDD+0.4V.

Reset value

0b000

[0]

Enable body-bias function:

0b0

: Bypass mode, or OFF if no external

bypass voltage is applied on VBBP and
VBBN.

0b1

: Body-bias enabled. BBGen is ON.

Reset value

0b0

SPARE_CTRL1 Register

The SPARE_CTRL1 Register characteristics are:

Purpose

Spare control register.

Usage constraints

There are no usage constraints.

Memory offset and full register reset value

See

3.11.2 SCC registers summary

on page 3-125

The following table shows the SPARE_CTRL1 Register bit assignments.

Table 3-118 SPARE_CTRL1 Register bit assignments

Bits

Name

Function

[31:0]

SPARE_CTRL1

Spare control register.

Software assigns the bit meanings.

Reset value

0x0000_0000

CHIP_ID Register

The CHIP_ID Register characteristics are:

3 Programmers model

3.11 Serial Configuration Control registers

101835_0000_01_en

reserved.

3-169

Non-Confidential

Содержание Musca-S1


































































































































































































Результаты поиска

Содержание Musca-S1

Отзывы:

Похожие инструкции для Musca-S1

Бренды по названию

Популярные бренды

ARM Musca-S1, Техническое справочное руководство

Результаты поиска

Содержание Musca-S1

Отзывы:

Похожие инструкции для Musca-S1

Бренды по названию

Популярные бренды