ARM Musca-S1 Скачать руководство пользователя страница 134

Страница: 134 / 194

Table 3-74 CTRL_BYPASS_DIV Register bit assignments (continued)

Bits

Name

Function

[2:1]

Reserved.

[0]

BYPASS_PLL_PREDIV_CLK

Bypass clock divider PREDIV:

0b0

: Not bypass.

0b1

: Bypass.

Reset value

0b1

PLL_CTRL_PLL0_CLK Register

The PLL_CTRL_PLL0_CLK Register characteristics are:

Purpose

Controls PLL0. Sets the internal oscillator target frequency and the output divider value.

Usage constraints

There are no usage constraints.

Memory offset and full register reset value

See

3.11.2 SCC registers summary

on page 3-125

The following table shows the PLL_CTRL_PLL0_CLK Register bit assignments.

Table 3-75 PLL_CTRL_PLL0_CLK Register bit assignment

Bits

Name

Function

[31:15] -

Reserved.

[14:12] PLL0_S

Controls the output divider that derives the
PLL0 output,

PLL0_CLK

, from the internal

oscillator frequency:

0b000

PLL0_CLK

INT_OSC

/1.

0b001

PLL0_CLK

INT_OSC

/2.

0b010

PLL0_CLK

INT_OSC

/4.

0b011

PLL0_CLK

INT_OSC

/8.

0b100

PLL0_CLK

INT_OSC

/16.

0b101

PLL0_CLK

INT_OSC

/32.

0b110

PLL0_CLK

INT_OSC

/64.

0b111

PLL0_CLK

INT_OSC

/128.

Reset value

0b000

[11:0]

PLL0_M

Controls the feedback divider of PLL0 to set
the target frequency of the internal oscillator:

INT_OSC

=4×PLL0_M×

PRE_PLL_CLK

Reset value

0x5F4

3 Programmers model

3.11 Serial Configuration Control registers

101835_0000_01_en

reserved.

3-134

Non-Confidential

Содержание Musca-S1


































































































































































































Результаты поиска

Содержание Musca-S1

Отзывы:

Похожие инструкции для Musca-S1

Бренды по названию

Популярные бренды

ARM Musca-S1, Техническое справочное руководство

Результаты поиска

Содержание Musca-S1

Отзывы:

Похожие инструкции для Musca-S1

Бренды по названию

Популярные бренды