ARM Musca-S1 Скачать руководство пользователя страница 162

Страница: 162 / 194

Table 3-107 SCC_MRAM_CTRL0 Register bit assignments (continued)

Bits

Name

Function

[8]

PG_VDD_0

eMRAM0 PG VDD:

0b0

: Powered up.

0b1

: Powered down.

Reset value

0b0

[7]

Reserved.

[6:5]

MRAM_DOUT_SEL

Select eMRAM0 output data.

0b00

: Wait one cycle for eMRAM output data

sample:

0b01

: Wait two cycles for eMRAM output

data sample.

0b10

: Wait three cycles for eMRAM output

data sample.

0b11

: Wait four cycles for eMRAM output

data sample (very long wait).

Reset value

0b00

[4]

FAST_READ_EN

Enable fast read:

0b0

: Normal read.

0b1

: Fast read

Reset value

0b0

[3]

MRAM_INV_CLK_SEL

Select clock inversion:

0b0

: Inverted.

0b1

: Not inverted.

Reset value

0b0

[2]

AUTOSTOP_EN

Enable autostop:

0b0

: Disabled.

0b1

: Enabled.

Reset value

0b0

[1]

PROC_SPEC_CLK_EN

Enable eMRAM controller clock:

0b0

: Disabled.

0b1

: Enabled.

Reset value

0b1

[0]

MRAM_CLK_EN

Enable eMRAM clock:

0b0

: Disabled.

0b1

: Enabled.

Reset value

0b1

3 Programmers model

3.11 Serial Configuration Control registers

101835_0000_01_en

reserved.

3-162

Non-Confidential

Содержание Musca-S1


































































































































































































Результаты поиска

Содержание Musca-S1

Отзывы:

Похожие инструкции для Musca-S1

Бренды по названию

Популярные бренды

ARM Musca-S1, Техническое справочное руководство

Результаты поиска

Содержание Musca-S1

Отзывы:

Похожие инструкции для Musca-S1

Бренды по названию

Популярные бренды