ARM Musca-S1 Скачать руководство пользователя страница 92 | Manualshive

Страница: 92 / 194

background image

Table 3-28 MHU registers (continued)

Offset

Name

Type Reset value

Description

0x0FD0

PIDR4

RO

0x0000_0004

Peripheral ID 4.

0x0FE0

PIDR0

RW

0x0000_0056

Peripheral ID 0.

0x0FE4

PIDR1

RO

0x0000_00B8

Peripheral ID 1.

0x0FE8

PIDR2

RO

0x0000_0000

Peripheral ID 2.

0x0FEC

PIDR3

WO

0x0000_0000

Peripheral ID 3.

0x0FF0

CIDR0

RO

0x0000_000D

Component ID 0.

0x0FF4

CIDR1

RO

0x0000_00F0

Component ID 1.

0x0FF8

CIDR2

RO

0x0000_0005

Component ID 2.

0x0FFC

CIDR3

RO

0x0000_00B1

Component ID 3.

3.4.9

AHB5 TrustZone Memory Protection Controllers

The Musca

‑

S1 test chip implements AHB5 TrustZone

Memory Protection Controllers

(MPCs) for

certain blocks including blocks in the base element.

The base memory addresses of the MPC APB configuration interfaces are in the Secure region. The base
memory addresses of the configuration interfaces in the base element are:

•

0x5008_3000

for internal SRAM bank 0.

•

0x5008_4000

for internal SRAM bank 1.

•

0x5008_5000

for internal SRAM bank 2.

•

0x5008_6000

for internal SRAM bank 3.

The following MPC base memory addresses are not in the base element but are shown here for
convenience:

In the Non-secure region:

•

0x4012_0000

for QSPI.

•

0x4013_0000

for SRAM.

•

0x4014_0000

for eMRAM.

In the Secure region:
•

0x5012_0000

for QSPI.

•

0x5013_0000

for SRAM.

•

0x5014_0000

for eMRAM.

The AHB5 TrustZone MPC gates transactions towards a memory interface when a security violation
occurs. The security checking is done based on block/page level which is configured externally by the
security controller through an APB interface.

The configuration registers can only be set by the security controller in the system with secure accesses
(PRTO[1]==0). Any type of access can read the identification registers.

APB accesses are internally aligned to word boundaries, so PADDR[1:0] bits are ignored. The
PSTRB[3:0] write strobe signals indicate which byte or bytes of the data bus contain valid data.

See the

Arm

®

CoreLink

™

SIE

‑

200 System IP for Embedded Technical Reference Manual

.

The following table shows the AHB5 TrustZone MPC registers in address offset order from the base
memory address. Undefined registers are reserved. Software must not attempt to access these registers.

3 Programmers model

3.4 Base element

101835_0000_01_en

Copyright © 2019, 2020 Arm Limited or its affiliates. All rights

reserved.

3-92

Non-Confidential

«
...
90
91
92
93
94
...
»

Содержание Musca-S1



































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Musca-S1

Бренд: NEILPRYDE Страницы: 53

Бренд: JAC Страницы: 103

Бренд: 3Disc Страницы: 12

Бренд: CAB Страницы: 13

Бренд: CAB Страницы: 30

Бренд: CAB Страницы: 17

Бренд: CAB Страницы: 33

Camping Equipment

Бренд: C. Crane Страницы: 8

Бренд: C-Pro Direct Страницы: 4

Бренд: C-Pro Direct Страницы: 4

Бренд: Raven Страницы: 17

Бренд: Campbell Страницы: 12

Бренд: Datavideo Страницы: 48

Бренд: Datavideo Страницы: 34

Бренд: Datavideo Страницы: 3

Бренд: Datavideo Страницы: 34

Бренд: Datavideo Страницы: 8

Бренд: Datavideo Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды