Arctic Cat Bearcat 570 2012 Скачать руководство пользователя

Страница: 9 / 76

Bearcat Z1 XT LTD/TZ1/TZ1 LXR

0745-804

F5 LXR

0745-213

Gasoline-Oil

Recommended Gasoline

The recommended gasoline to use in these

snowmobiles is 87 octane regular unleaded.

In many areas, oxygenates (either ethanol

or MTBE) are added to the gasoline. Oxy-

genated gasolines containing up to 10%

ethanol or up to 15% MTBE are acceptable

gasolines; however, on the 570 cc models

whenever using oxygenated gasolines, the

carburetor main jet must be one size larger

than the main jet required for regular

unleaded gasoline. For example, if a 220

main jet is recommended for regular

unleaded gasoline, a 230 main jet must be

installed if using an oxygenated gasoline.



NOTE: The TZ1 Turbo model will

detect lower octane gasoline and
reduced engine performance will
result. It is recommended that 91
octane (minimum) gasoline be used
in this model.

When using ethanol blended gasoline, it is

not necessary to add a gasoline antifreeze

since ethanol will prevent the accumula-

tion of moisture in the fuel system.

CAUTION

If a situation arises wherein 91 octane
gasoline is not available, 87 octane
gasoline can be substituted; how-
ever, do not prolong the usage of 87
octane gasoline as it will cause poor
engine performance.

CAUTION

Do not use white gas or gasolines
containing methanol. Only Arctic Cat
approved gasoline additives should
be used.

Содержание Bearcat 570 2012













































































Результаты поиска

Содержание Bearcat 570 2012

Отзывы:

Похожие инструкции для Bearcat 570 2012

Бренды по названию

Популярные бренды

Arctic Cat Bearcat 570 2012, Руководство оператора

Результаты поиска

Содержание Bearcat 570 2012

Отзывы:

Похожие инструкции для Bearcat 570 2012

Бренды по названию

Популярные бренды