Arctic Cat Bearcat 570 2012 Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 76

background image

54

Overload Springs

Some models have overload springs built

into the rear suspension. When either car-

rying a heavy load or riding 2-up, the

overload springs should be engaged by

rotating the spring tension blocks to the

UP position. The spring tension blocks

lock in an over-center position when

engaged.



NOTE: Arctic Cat recommends

that the overload springs be
engaged whenever a load on the
snowmobile (operator/passenger/
cargo) exceeds 136 kg (300 lb).

To either engage or disengage the spring

tension blocks, use a spark plug socket

and a screwdriver to adjust the spring

block to the desired position. Make sure

both spring blocks are in the same posi-

tion (either engaged or disengaged).

744-457A

Lights

For the correct headlight bulb and/or tail-

light/brakelight LED, see the appropriate

specifications sheet.

Removing and Installing

Taillight/Brakelight (F5

LXR/F570 Models)

These models are equipped with an LED

taillight/brakelight. If the LED fails, it

must be replaced. To remove and install

the LED, use the following procedure.



NOTE: To access the harness con-

nector and the two self-tapping
screws securing the taillight to the
snowflap, compress the two flanged
tabs (located on the under-side of
the tunnel) and carefully pry up on
the front of the taillight/snowflap.

0744-462

1. Disconnect the taillight harness con-

nector.

2. Remove the two self-tapping screws

securing the taillight to the snowflap.

3. Secure the taillight to the snowflap

with the two self-tapping screws;

then connect the taillight connector.

4. Secure the front of the snowflap to

the tunnel by carefully tapping the

snowflap until the two flanged tabs

snap into place.

Removing and Installing

Taillight/Brakelight

(Bearcat XT Models)

1. Remove the four pins securing the

rear seat to the seat/Speedrack mount.

743-329A

CAUTION

There are weight limitations for these
snowmobiles. If additional cargo is
being added, maximum weight on the
snowmobile (operator/passenger/
cargo) should not exceed the maxi-
mum limitation set for each snowmo-
bile. See chart for details. Also, the
overload springs should be engaged.

Maximum Weight Limitations

Bearcat 570

170 kg

375 lb

Bearcat 570 XT

272 kg

600 lb

Bearcat Z1 XT

272 kg

600 lb

T570/TZ1

170 kg

375 lb

«
...
56
57
58
59
60
...
»

Содержание Bearcat 570 2012













































































Отзывы:

Нет отзывов

Похожие инструкции для Bearcat 570 2012

Бренд: Yard-Man Страницы: 20

Бренд: Yamaha Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды