Arctic Cat Bearcat 570 2012 Скачать руководство пользователя | Manualshive

Страница: 59 / 76

background image

55



NOTE: On the LTD model, also

remove the two pins securing the
third seat to the seat/Speedrack
mount; then lift the third seat up and
away.

0745-131

2. Lift on the back of the rear seat and

move rearward to remove it from the

mount.

3. Compress the latch on the right side

of the front seat and lift the front seat

away; then disconnect the taillight

harness connector.

743-444A

4. Loosen (but do not remove) the

three right-side seat/Speedrack

mount cap screws.

5. Carefully route the harness connec-

tor through the hole in the storage

compartment panel; then remove the

harness from beneath the seat/Spee-

drack mount.

6. Remove the two self-tapping screws

securing the taillight to the bumper;

then route the harness out of the

bumper and remove the taillight.

7. Route the taillight harness through

the bumper; then secure the taillight

to the bumper with the two self-tap-

ping screws.

8. Carefully route the harness beneath the

Speedrack mount and through the hole

in the storage compartment panel; then

connect the harness connector.

9. Tighten the three right-side mount

cap screws; then lower the front seat.

10. Place the rear seat into position on

the mount making sure the four pin

holes are properly aligned with the

mounting location on the mount.

11. Install the four pins making sure

they are properly seated.



NOTE: On the LTD model, place

the third seat into position on the
mount making sure the two pin holes
are properly aligned with the mount-
ing location on the mount; then
install the two pins making sure they
are properly seated.

Removing and Installing

Taillight/Brakelight Bulb

(Bearcat 570/T570/TZ1

Models)

1. Remove the torx-head cap screws

securing the taillight access panel.

742-467A

2. Disconnect the harness connector

and remove housing.

3. Push in on the socket and rotate it

counterclockwise to remove it from

the housing.

4. Remove the old bulb by pulling it

straight out of the socket.

! WARNING

Make sure the rear seat (and on the
LTD model, the third seat) is securely
locked in place with the pins before
carrying a passenger or personal
injury may result.

«
...
57
58
59
60
61
...
»

Содержание Bearcat 570 2012













































































Отзывы:

Нет отзывов

Похожие инструкции для Bearcat 570 2012

Бренд: Ski-Doo Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды