Arctic Cat Bearcat 570 2012 Скачать руководство пользователя страница 57

Страница: 57 / 76

The length adjustment of the front arm

limiter straps determines the weight distri-

bution between the front of the skid frame

and the skis. Tightening the limiter strap

(shortening the strap) will pull up on the

front of the skid frame and will increase ski

pressure. Loosening the limiter strap

(lengthening the strap) lowers the front of

the skid frame and decreases ski pressure.
When customizing the amount of ski

pressure, be sure to adjust both straps

equally and do not over-adjust the limiter

straps to adversely affect steering and

operator control of the snowmobile.

Some experimentation may be required

until the proper adjustment for the opera-

tor’s individual style is obtained.



NOTE: If the limiter straps are

adjusted, it is highly recommended that
at least a minimum of 1/8 in. preload on
the shock spring be maintained.

Adjusting Rear Spring Pre-

Load

Proper adjustment of rear spring pre-load

is necessary to get the most desirable

ride. The chart is designed to help in set-

ting up rear spring pre-load; however,

riding style is the single greatest factor in

determining rear spring requirements.



NOTE: These cam position set-

tings are suggestions only. Personal
riding style will greatly influence
cam position settings. Spend time to
determine setting preferences.

Rear spring pre-load adjustment is accom-

plished by rotating the adjusting cams. Posi-

tion 3 provides the stiffest ride, and position 1

is for a light driver or slow-speed trail riding.

Position 2 is for an average operator under

normal conditions. Always rotate the cam

from the lighter position to heavier position.

741-450A

To rotate an adjusting cam, use the spark

plug wrench from the tool kit. Rotate the

wrench until the cam is in the desired

position. To stiffen the ride, rotate the cam

so as to raise the spring end. Make the

appropriate adjustment on the other cam.

Articulating Skid Frame

(Bearcat XT Models)

The rear articulating portion of the skid

frame has two skid frame adjusters which

control the amount of travel in the rear

suspension.
These two adjusters have been pre-set at

the factory and should require no further

adjustment.
If adjustment is ever required, rotate the

two adjusters equally to permit 12.5-25

mm (1/2-1 in.) travel of the articulating

portion of the suspension.

0743-323



NOTE: Tightening the adjusters

will stiffen the articulating skid frame
travel; loosening the adjusters will
soften the travel.

! WARNING

Do not adjust the front arm limiter
straps to a point at which steering
and operator control of the snowmo-
bile are adversely affected.

Rider Weight (lb)

Cam Position

Up to 180

180-240

Over 240

CAUTION

Never force the adjustment cams
from the low position to the high
position. Cam damage may occur.

Содержание Bearcat 570 2012













































































Результаты поиска

Содержание Bearcat 570 2012

Отзывы:

Похожие инструкции для Bearcat 570 2012

Бренды по названию

Популярные бренды

Arctic Cat Bearcat 570 2012, Руководство оператора

Результаты поиска

Содержание Bearcat 570 2012

Отзывы:

Похожие инструкции для Bearcat 570 2012

Бренды по названию

Популярные бренды