Arctic Cat Bearcat 570 2012 Скачать руководство пользователя страница 17

Страница: 17 / 76

The icon should illuminate each time the

ignition switch is turned to RUN or

START, and it should go out when the

engine starts. If the icon illuminates

while the engine is running, oil pressure

has been lost and the engine will auto-

matically shut off.
If oil pressure is lost, use the following

procedure to check the oil level:

1. With the engine off, remove the

engine oil level stick and wipe it

clean. Without screwing it in, set the

stick back in the oil tank. Remove it

and observe the oil level on the

stick. If the oil level is at or below

the ADD mark on the oil level stick,

add only enough recommended oil

to raise the level to the NORMAL

range. DO NOT overfill the reser-

voir with oil.

2. Open the air bleed bolt located on

the oil pump (beneath the coolant

tank) to purge air from the oil hose.

ZJ004A



NOTE: When air can no longer be

heard purging from oil pump bleed,
tighten the bleed bolt to 7.5 ft-lb.

3. Start the engine. The warning icon

should go out within five seconds.

4. If the warning icon does not go out,

shut the engine off immediately and

repeat step 2; then repeat step 3.

If the warning icon does not go out or if

the engine does not start, take the snow-

mobile to an authorized Arctic Cat Snow-

mobile dealer. If not under warranty, this

service is at the discretion and expense of

the snowmobile owner.

Diagnostic Codes (F5

LXR/Bearcat Z1 XT/TZ1

Models)

Diagnostic codes are activated by the

ECU and may be displayed on the read-

out screen for a number of reasons.
If a code is displayed while the engine is

running, the ECU is receiving input that

is outside of its established parameters. If

a code has been activated, take the snow-

mobile to an authorized Arctic Cat Snow-

mobile dealer for service. If not under

warranty, this service is at the discretion

and expense of the snowmobile owner.

F5 LXR Model

Bearcat Z1 XT/TZ1

Models

CAUTION

Do not attempt to start the engine
with the bleed bolt open.

Code

Trouble

Failure in injector(s).

Open or short circuit in barometric

pressure sensor.

Open or short circuit in intake air tem-

perature sensor.

Open or short circuit in water tempera-

ture sensor.

Open or short circuit in throttle position

sensor.

Failure in ignition coil.

Code

Trouble

Failure in the fuel system.

Failure in injector (PTO).

Failure in injector (MAG).

Failure in barometric pressure sensor.

Open or short circuit in intake manifold

air temperature sensor.

Open or short circuit in water tempera-

ture sensor.

Open or short circuit in throttle posi-

tion sensor.

Open or short circuit in manifold air

pressure sensor.

Failure in crankshaft position sensor.

Failure in speed sensor.

Failure in coil (MAG).

Failure in coil (PTO).

Failure in ISC valve.

Failure in oxygen sensor.

Failure in camshaft position sensor.

Failure in knock sensor.

22*

Failure in injector (PTO secondary).

Содержание Bearcat 570 2012













































































Результаты поиска

Содержание Bearcat 570 2012

Отзывы:

Похожие инструкции для Bearcat 570 2012

Бренды по названию

Популярные бренды

Arctic Cat Bearcat 570 2012, Руководство оператора

Результаты поиска

Содержание Bearcat 570 2012

Отзывы:

Похожие инструкции для Bearcat 570 2012

Бренды по названию

Популярные бренды