manualshive.com logo in svg

Arctic Cat Bearcat 570 2012, Руководство оператора

Описание продукта: Arctic Cat Bearcat 570 2012. Пользовательский мануал доступен для загрузки бесплатно на manualshive.com. Операторский мануал содержит все необходимые инструкции по эксплуатации данной модели. Необходимо загрузить его, чтобы правильно использовать Arctic Cat Bearcat 570 2012.

Поделиться
Скачать
background image

14

* Turbo model

Handlebar Tilt

Standard Block Style

The handlebar can be adjusted to the

operator’s preference. To adjust the han-

dlebar, use the following procedure:

NOTE: It may be necessary to

remove the handlebar cover for this
procedure.

1. Loosen the four lock nuts  securing

the handlebar caps and block to the

steering post.

743-442A

2. Adjust the handlebar to operator’s

desired tilt; then tighten the lock

nuts evenly and securely. Check

steering for maximum right/left

turning capabilities.

NOTE: Do not adjust the handlebar

to a position that allows air to enter
the brake system.

3. Recheck lock nuts; tighten securely.

NOTE: Recommended torque

value of lock nuts is 18 ft-lb. 

Riser Block Style

The handlebar can be adjusted to the

operator’s preference. To adjust the han-

dlebar, use the following procedure:

1. Loosen the four cap screws and lock

nuts securing the handlebar caps to the

riser and the riser to the steering post.

744-439A

2. Adjust the handlebar to operator’s

desired tilt, tighten the lock nuts/cap

screws evenly to 25 ft-lb, and check

steering for maximum right/left

turning capabilities.

NOTE: Do not rotate the handlebar

to a position that allows air to enter
the brake system. 

Cam Lever Style

The handlebar can be adjusted to the

operator’s preference. To adjust the han-

dlebar, use the following procedure:

1. Press inward on the lock pin to

release the cam lever and “flip” the

cam lever up.

741-427A

23*

Failure in injector (MAG secondary).

25

Failure in shifting system/gear position 

switch.

26

Malfunction in air pressure sensor.

29

Malfunction in shift control switch.

OCTN*

Low octane gasoline.

! WARNING

Tighten lock nuts according to specifi-
cations to prevent unexpected “move-
ment” of the handlebar during
operation over rough terrain. DO NOT
position handlebar so steering (maxi-
mum right/left turning capabilities) or
throttle and brake controls are affected.

Code

Trouble

! WARNING

Tighten lock nuts/cap screws accord-
ing to specifications to prevent unex-
pected “movement” of the handlebar
during operation over rough terrain.
DO NOT position the handlebar so
steering (maximum right/left turning
capabilities) or throttle and brake
controls are affected.

Содержание Bearcat 570 2012













































































Отзывы:

Нет отзывов

Похожие инструкции для Bearcat 570 2012

Yamaha RX10K Assembly Manual preview
RX10K
Бренд: Yamaha Страницы: 98

Бренды по названию

Популярные бренды

Загрузить еще бренды