Arctic Cat Bearcat 570 2012 Скачать руководство пользователя страница 36

Страница: 36 / 76

741-335A

On the F5 LXR/F570 models, turn the

handlebar to the right; then from the right

side, pump grease into the steering arms

until grease is noted coming out of either

end of the arms. Wipe excess grease from

the arms.

0741-440

Rear Suspension

This procedure should be done every 40

operating hours.



NOTE: Arctic Cat recommends

that Arctic Cat All-Temp Grease (p/n
4639-365) be used for this proce-
dure.



NOTE: Illustrated are the general

locations of grease fittings. Actual
locations will vary from model to
model.

1. Shut engine off and wait for all mov-

ing parts to stop.

2. With the gas tank nearly empty (less

than 1/4 full) and using Handlebar

Stand (p/n 5639-152) or a suitable

substitute, lay the snowmobile on its

left side.

3. Remove ice and snow buildup from

the skid frame to expose the grease

fittings.

0741-376

4. Lubricate the grease fittings with all-

temperature grease.

F5 LXR/F570 Models

Содержание Bearcat 570 2012













































































Результаты поиска

Содержание Bearcat 570 2012

Отзывы:

Похожие инструкции для Bearcat 570 2012

Бренды по названию

Популярные бренды

Arctic Cat Bearcat 570 2012, Руководство оператора

Результаты поиска

Содержание Bearcat 570 2012

Отзывы:

Похожие инструкции для Bearcat 570 2012

Бренды по названию

Популярные бренды