Arctic Cat Bearcat 570 2012 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 76

background image

48

Checking/Adjusting Drive

Belt Deflection

0743-319

The drive belt must have the proper fit in

the drive clutch and driven pulley. To

check for proper drive belt fit, use the

following procedure.

1. Place a straightedge on the top of the

drive belt. The straightedge should

reach from the drive clutch to the top

of the driven pulley.



NOTE: Make sure the drive belt is

all the way out in the driven pulley
before checking drive belt fit.

2. Using a stiff ruler centered between

the drive clutch and driven pulley,

push down on the drive belt just

enough to remove all slack and note

the amount of deflection. The

deflection should be within the

range of 28.5-31.8 mm (1 1/8-1 1/4

in.).

3. To correct drive belt deflection,

remove the sheave adjuster from the

pulley, remove or add shim washers

to the adjuster, and install the

adjuster.



NOTE: Adding shim washers will

decrease belt deflection and remov-
ing shim washers will increase belt
deflection. Available shim washers
from Arctic Cat are p/n 0648-714
(0.090 in.) - one included in the tool
kit, p/n 0648-715 (0.030 in.), and p/n
0648-716 (0.060 in.).



NOTE: Removing/adding shim

washers may be done by the snow-
mobile owner if qualified to do so. If
the owner does not feel qualified,
take the snowmobile to an autho-
rized Arctic Cat Snowmobile dealer
for this service. This service is at the
discretion and expense of the snow-
mobile owner.

Removing Drive Belt



NOTE: Changing a drive belt can

be done by the snowmobile owner if
qualified to do so. If the owner does
not feel qualified, take the snowmo-
bile to an authorized Arctic Cat
Snowmobile dealer for this service.
This service is at the discretion and
expense of the snowmobile owner.

1. Turn ignition key to the OFF posi-

tion and wait for all moving parts to

stop.

2. Set the brake lever lock.
3. Open the left-side access panel; then

remove the belt guard.

4. Remove the cap screw, lock washer,

washer, and sheave adjuster from the

end of the driven pulley.



NOTE: Assure that the shims and

O-ring are not removed from the
adjuster.

0743-395

5. Remove the cap screw (w/lock

washer and washer) from the

adjuster, remove the washer and

lock washer from the cap screw, turn

the adjuster around (reverse it), and

insert the cap screw into the adjuster.

CAUTION

Never run the engine with the drive
belt removed. Excessive revving of
the engine could result in serious
engine damage and drive clutch fail-
ure.

«
...
50
51
52
53
54
...
»

Содержание Bearcat 570 2012













































































Отзывы:

Нет отзывов

Похожие инструкции для Bearcat 570 2012

Бренд: Ski-Doo Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды