Arctic Cat Bearcat 570 2012 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 76

background image

22

743-329A



NOTE: On the LTD model, also

remove the two pins securing the third
seat to the seat/Speedrack mount;
then lift the third seat up and away.

0745-131

2. Lift on the back of the rear seat and

move it rearward to remove it from

the mount.

To install the rear seat (and on the LTD

model, the third seat), use the following

procedure:

1. Place the rear seat into position on

the mount making sure the four pin

holes are properly aligned with the

mounting location on mount.

2. Install the four pins making sure

they are properly seated.



NOTE: On the LTD model, place

the third seat into position on the
mount making sure the two pin holes
are properly aligned with the mount-
ing location on the mount; then
install the two pins making sure they
are properly seated.

Removable Light Bar

(Bearcat Z1 XT GS

Model)

This snowmobile is equipped with a

removable light bar. To remove and

install, use the following procedure.

1. Disconnect the light bar harness

connector; then remove the four pins

securing the bar to the mount.

0745-805

2. Remove the light bar.

3. Place the light bar into position on the

mount; then secure with the four pins.

4. Connect the light bar harness connector.

Winch (Bearcat Z1 XT

GS Model)

This snowmobile is equipped with a winch.

There are two mounting locations. The

front mounting location is for actual use of

the winch (see the winch guide) and should

not remain in this location when operating

the snowmobile. The tunnel mounting loca-

tion is for “storing” the winch when not in

use and should remain in this location when

operating the snowmobile.
To relocate the winch, use the following

procedure.

1. Remove the receiver pin and the hair-

pin clip securing the winch.

0745-806

! WARNING

Make sure the rear seat (and on the
LTD model, the third seat) is securely
locked in place with the pins before
carrying a passenger or personal
injury may result.

«
...
24
25
26
27
28
...
»

Содержание Bearcat 570 2012













































































Отзывы:

Нет отзывов

Похожие инструкции для Bearcat 570 2012

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды