manualshive.com logo in svg

Arctic Cat Bearcat 570 2012, Руководство оператора

Описание продукта: Arctic Cat Bearcat 570 2012. Пользовательский мануал доступен для загрузки бесплатно на manualshive.com. Операторский мануал содержит все необходимые инструкции по эксплуатации данной модели. Необходимо загрузить его, чтобы правильно использовать Arctic Cat Bearcat 570 2012.

Поделиться
Скачать
background image

27

5. Pumping the brake lever is permissible;

however, if pumping the brake lever

more than twice is necessary to obtain

the necessary stopping power, immedi-

ately take the snowmobile to an autho-

rized Arctic Cat Snowmobile dealer for

service. If not under warranty, this ser-

vice is at the discretion and expense of

the snowmobile owner.

6. When new brake pads are installed, a

“burnishing” process is required. Drive

the snowmobile slowly and compress

the brake lever several times until the

pads just start to heat up; then allow

them to thoroughly cool down. This

process stabilizes the pad material and

extends the life of the pads.

Emergency Stopping

There are several methods of stopping or

slowing the snowmobile under a variety

of situations. Identified in the following

chart are the ways a snowmobile may be

brought to a stop and the effectiveness

under normal conditions.

Throttle/Ignition 

Monitor Switch

The throttle control is equipped with a

monitor switch for safety purposes which

will stop the engine when a loss of return

spring force occurs. If ice forms in the

throttle system or if there is some other

malfunction of the throttle system result-

ing in a loss of return spring force, the

monitor switch will stop the engine when

the throttle control lever is released.

If the snowmobile engine stops abruptly

when the throttle control lever is released

and the activation of the monitor switch is

suspected, use the following procedure:

1. Rotate the ignition key to the OFF

position.

2. Remove ice and snow from the

throttle system and wait 5-10 min-

utes for the engine heat to thaw ice

from the throttle system.

3. Test the throttle control lever by

compressing and releasing it several

times. The lever MUST return to the

idle position quickly and completely.

NOTE: If the throttle control lever

operates properly and the engine
does not start, compress the throttle
lever slightly (approximately 1/8
throttle) and try starting the engine.
If the engine now starts and stops
when the throttle lever is released,
take the snowmobile to an autho-
rized Arctic Cat Snowmobile dealer
for service. If not under warranty,
this service is at the discretion and
expense of the snowmobile owner.

4. If the throttle control lever operates

properly, rotate the ignition key to

the RUN position and go through

normal starting procedures.

Item

Function

Condition

Emergency 

Stop Switch

interrupts igni-

tion circuit

ALL

Throttle/Ignition 

Monitor Switch

interrupts igni-

tion circuit

ALL

Ignition Switch

interrupts igni-

tion circuit

ALL

Brake

slows the drive 

system

ALL

Choke (570 cc 

models)

floods the engine 1/2 throt-

tle or less

! WARNING

If any malfunction of the throttle sys-
tem occurs (such as freezing in fluffy
snow) and the monitor switch does
not shut off the engine, press down
on the emergency stop switch IMME-
DIATELY to stop the engine. DO NOT
start the engine until the malfunction
in the throttle system has been
located and corrected.

! WARNING

If the throttle control lever does not
work properly, DO NOT ATTEMPT TO
START THE ENGINE.

Содержание Bearcat 570 2012













































































Отзывы:

Нет отзывов

Похожие инструкции для Bearcat 570 2012

Бренды по названию

Популярные бренды

Загрузить еще бренды