manualshive.com logo in svg

Arctic Cat Bearcat 570 2012, Руководство оператора

Описание продукта: Arctic Cat Bearcat 570 2012. Пользовательский мануал доступен для загрузки бесплатно на manualshive.com. Операторский мануал содержит все необходимые инструкции по эксплуатации данной модели. Необходимо загрузить его, чтобы правильно использовать Arctic Cat Bearcat 570 2012.

Поделиться
Скачать
background image

45

NOTE: On the Bearcat Z1 XT GS

model, the towing accessories fuses
are located beneath the seat.

2. Remove the suspected fuse.
3. Look through the clear side of the

fuse to see if the metal wire inside is

separated. If it is, the fuse is blown

and should be replaced with a fuse of

the correct amperage rating.

4. On the 1100 cc models, install the fuse

panel cover and close the right-side

access panel. On the F5 LXR/570 cc

models, install the fuse holder cover.

Even after replacing a fuse, it may continue

to blow if the cause of the overload is not

determined. If the fuse continues to blow,

take the snowmobile to an authorized Arctic

Cat Snowmobile dealer for service. If not

under warranty, this service is at the discre-

tion and expense of the snowmobile owner.

Brake System

Arctic Cat recommends that the brake

system (brake lever, fluid reservoir, hose,

caliper, pads, and brake disc) be checked

daily for fluid leakage, wear, or damage

and for proper operation. Also, the brake

fluid level must be checked every time

before starting the engine. The brake

fluid must be visible in the sight glass.

Checking/Adding Brake 

Fluid

1. With sight glass reservoir in a level

position, check the fluid level. The

brake fluid level must be visible in

the sight glass.

NOTE: If the sight glass appears

dark, there is a sufficient amount of
fluid in the reservoir.

741-328A

2. If the brake fluid is not visible in the

sight glass, remove the reservoir cover

and add Arctic Cat approved brake

fluid until the fluid is at the recom-

mended level. Install and secure the

reservoir cover. Do not allow moisture

to contaminate the brake system.

Changing Brake Fluid

The brake fluid must be changed on a reg-

ular basis and whenever the brake fluid has

been overheated or contaminated. The

brake fluid should be changed every 1000

miles or at the end of the snowmobiling

season, whichever occurs first. Take the

snowmobile to an authorized Arctic Cat

Snowmobile dealer for this service. This

service is at the discretion and expense of

the snowmobile owner.

Checking Brake Lever 

Travel

Before each use, check the brake lever

travel using the following procedure:

1. Compress the brake lever fully.

! WARNING

Always replace a fuse with one hav-
ing the same specified amperage rat-
ing. Using a fuse with a higher rating
can cause severe wire damage and
could start a fire.

! WARNING

DO NOT operate the snowmobile
when the brake lever lock is engaged
or when any component in the brake
system is damaged, worn, or
adjusted improperly. If the snowmo-
bile is operated and the brake system
is not functioning properly, severe
personal injury could result.

CAUTION

Brake fluid is highly corrosive. Do not
spill brake fluid on any surface of the
snowmobile.

! WARNING

Do not overfill the brake fluid reser-
voir. Overfilling the reservoir may
cause the brake system to hydrauli-
cally lock. Use only Arctic Cat
approved brake fluid. Never substi-
tute or mix different types or grades
of brake fluid. Brake loss can result.
Brake loss can result in severe injury
or even death.

Содержание Bearcat 570 2012













































































Отзывы:

Нет отзывов

Похожие инструкции для Bearcat 570 2012

Бренды по названию

Популярные бренды

Загрузить еще бренды