Arctic Cat Bearcat 570 2012 Скачать руководство пользователя

Страница: 27 / 76

2. Place the winch in the desired posi-

tion; then secure it with the hairpin

clip and the receiver pin.



NOTE: When operating the snow-

mobile, always have the winch in the
tunnel mounting location secured with
the hairpin clip and the receiver pin.

Removable/Adjustable

Seat (F5 LXR Model)

This snowmobile is equipped with a

removable/adjustable seat. To adjust the

seat, use the following procedure:

1. Press in on the left-end of the seat

adjuster lever at the rear storage

compartment; then pull out on the

seat adjuster lever at the rear storage

compartment.

0744-465

2. Lift up on the back of the seat; then

move the front of the seat up or

down into one of the seven available

positions.

3. Press down on the rear of the seat;

then secure the seat by releasing the

seat adjuster lever.

To remove the seat, use the following

procedure:

1. Adjust the seat to the lowest posi-

tion; then while lifting on the top

forward part of the seat, remove the

self-tapping screw from the right

side of the seat support assembly.

741-718A

2. Press in on the left-end of the seat

adjuster lever at the rear storage

compartment; then pull out on the

seat adjuster lever.

3. Lift on the back of the seat and move

it forward and upward to remove it

from the chassis.

To install the seat, use the following pro-

cedure:

1. With the seat adjuster lever pulled

out, slide the front of the seat into

position on the chassis; then with

seat position selected, lower the rear

of the seat onto the rear storage com-

partment.

2. Press down on the rear of the seat;

then secure the seat by releasing the

seat adjuster lever.

3. With the seat adjusted to the lowest

position, install the self-tapping

screw into the right side of the seat

support assembly.

Towing

If the snowmobile is to be towed by

another snowmobile, do not tow using

the loops in the skis. The tow rope should

be attached to the spindles.

CAUTION

Do not use the adjuster lever to lift
the seat.

! WARNING

Make sure the seat is securely locked
in place or personal injury may result.

CAUTION

Do not use the adjuster lever to lift
the seat.

! WARNING

Make sure the self-tapping screw is
securely tightened and the seat is
securely locked in place or personal
injury may result.

Содержание Bearcat 570 2012













































































Результаты поиска

Содержание Bearcat 570 2012

Отзывы:

Похожие инструкции для Bearcat 570 2012

Бренды по названию

Популярные бренды

Arctic Cat Bearcat 570 2012, Руководство оператора

Результаты поиска

Содержание Bearcat 570 2012

Отзывы:

Похожие инструкции для Bearcat 570 2012

Бренды по названию

Популярные бренды