Arctic Cat Bearcat 570 2012 Скачать руководство пользователя

Страница: 67 / 76

15. Clean and polish the hood, console,

and chassis with Cat Cleaner (p/n

4639-371). DO NOT USE SOL-

VENTS. THE PROPELLANT

WILL DAMAGE THE FINISH.



NOTE: On electric start models,

disconnect the battery cables making
sure to disconnect the negative cable
first; then clean the battery posts and
cables. Charge the battery.

16. If possible, store the snowmobile

indoors. Raise the track off the floor

by blocking up the back end making

sure the snowmobile is secure.

Loosen the track adjusting bolts to

reduce track tension. Cover the

snowmobile with a machine cover or

a heavy tarpaulin to protect it from

dirt and dust.

17. If the snowmobile must be stored out-

doors, position the snowmobile out of

direct sunlight; then block the entire

snowmobile off the ground making

sure the snowmobile is secure. Loosen

the track adjusting bolts to reduce

track tension. Cover with a machine

cover or a heavy tarpaulin to protect it

from dirt, dust, and rain.

CAUTION

Sealed batteries require charging if
left for extended non-start periods.
Arctic Cat recommends trickle charg-
ing once a month. Follow the manu-
facturer’s instructions and cautions.

CAUTION

Avoid storing in direct sunlight and
using a plastic cover as moisture may
collect on the snowmobile causing
corrosion.

Содержание Bearcat 570 2012













































































Результаты поиска

Содержание Bearcat 570 2012

Отзывы:

Похожие инструкции для Bearcat 570 2012

Бренды по названию

Популярные бренды

Arctic Cat Bearcat 570 2012, Руководство оператора

Результаты поиска

Содержание Bearcat 570 2012

Отзывы:

Похожие инструкции для Bearcat 570 2012

Бренды по названию

Популярные бренды