Arctic Cat Bearcat 570 2012 Скачать руководство пользователя

Страница: 55 / 76

Track Alignment

Proper track alignment is obtained when

the rear idler wheels are equal distance

from the inner track drive lugs. Excessive

wear to the idler wheels, drive lugs, and

track will occur if the track is improperly

aligned. Arctic Cat recommends that the

track alignment be checked once a week

or whenever the track tension is adjusted.

Checking Track Alignment

1. Remove excess ice and snow

buildup from the track, track drive

sprockets, and the inside of the skid

frame.

2. Position the tips of the skis against a

wall; then using a shielded safety

stand, raise the rear of the snowmo-

bile off the floor making sure the

track is free to rotate.

3. Start the engine and accelerate

slightly. Use only enough throttle to

turn the track several revolutions.

SHUT ENGINE OFF.



NOTE: Allow the track to coast to a

stop. DO NOT apply the brake
because it could produce an inaccu-
rate alignment condition.

4. When the track stops rotating, check

the relationship of the rear idler

wheels and the inner track drive lugs.

If the rear idler wheels are centered

between the inner track drive lugs, no

adjustment is necessary.

725-070A

5. If the idler wheels are not centered

between the inner track drive lugs,

an adjustment is necessary.

Adjusting Track Alignment

1. On the side of the track which has

the inner track drive lugs closer to

the rear idler wheel, loosen the

adjusting bolt jam nut; then rotate

the adjusting bolt clockwise 1 to 1 1/

2 turns.

739-636B



NOTE: On the Bearcat XT models,

the rear axle cap screws must also
be loosened.

743-323A

2. Check track alignment and continue

adjustment until proper alignment is

obtained.



NOTE: Make sure correct track

tension is maintained after adjust-
ing track alignment (see Track Ten-
sion sub-section in this section).

! WARNING

Make sure the ignition key is in the
OFF position and the track is not
rotating before checking or adjusting
track alignment. Personal injury
could result if contact is made with a
rotating track.

! WARNING

The tips of the skis must be posi-
tioned against a wall or similar object.

! WARNING

DO NOT stand behind the snowmo-
bile or near the rotating track. NEVER
run the track at high speed when the
track is suspended.

Содержание Bearcat 570 2012













































































Результаты поиска

Содержание Bearcat 570 2012

Отзывы:

Похожие инструкции для Bearcat 570 2012

Бренды по названию

Популярные бренды

Arctic Cat Bearcat 570 2012, Руководство оператора

Результаты поиска

Содержание Bearcat 570 2012

Отзывы:

Похожие инструкции для Bearcat 570 2012

Бренды по названию

Популярные бренды