Arctic Cat Bearcat 570 2012 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 76

background image

21

When riding single, the backrest can be

moved to the forward seat position.

To move the backrest, pull the adjuster

out and down, pull the backrest up and

out of the slots, slide the backrest into the

slots of the seat and adjust to the desired

position, and push the adjuster up and in

to lock the backrest in place.



NOTE: If moving the backrest to

the forward seat position, the pas-
senger seat must be removed.



NOTE: When removing/adjusting

the backrest on the standard T570/
TZ1 passenger seat, loosen, but do
not remove, the cap screw at the rear
of seat, install/adjust the passenger
seat, and tighten the cap screw
securely.

Removable Rear Seat

Bearcat 570/T570/TZ1

Models

These snowmobiles are equipped with a

removable rear seat to allow for addi-

tional cargo space when no passenger is

being carried.



NOTE: If additional cargo is being

added, maximum weight on the
snowmobile (operator/passenger/
cargo) should not exceed the maxi-
mum limitation set for each snowmo-
bile. See the chart in the Suspension
- Overload Springs sub-section in
the Maintenance section for details.
Also, the overload springs should be
engaged.

To remove the rear seat, use the follow-

ing procedure:



NOTE: On LXR models, the center

luggage bag must be removed.

1. Rotate the seat latch either clock-

wise or counterclockwise and hold it

in that position; then lift the seat and

move it rearward far enough to

access the electrical connector.

742-593A

2. Unplug the electrical connector; then

remove the seat from the tunnel.

To install the seat, use the following pro-

cedure:

1. Place the seat into position on the

tunnel; then plug in the electrical

connector.

2. Rotate the seat latch either clock-

wise or counterclockwise and hold it

in that position; then slide the seat

forward, allow it to settle into posi-

tion, and release the latch to lock the

seat securely.

Bearcat XT Models

These snowmobiles are equipped with a

removable rear seat (and on the LTD

model, a removable third seat) to allow

for additional cargo space when no pas-

senger is being carried.



NOTE: If additional cargo is being

added, maximum weight on the
snowmobile (operator/passenger/
cargo) should not exceed the maxi-
mum limitation set for each snowmo-
bile. See the chart in the Suspension
- Overload Springs sub-section in
the Maintenance section for details.
Also, the overload springs should be
engaged.

To remove the rear seat (and third seat on

the LTD model), use the following proce-

dure:

1. Remove the four pins securing the rear

seat to the seat/Speedrack mount.

! WARNING

Moving the backrest to the forward
seat position limits the seating
capacity to one person only.

! WARNING

Make sure the rear seat is securely
locked in place before carrying a pas-
senger or personal injury may result.

«
...
23
24
25
26
27
...
»

Содержание Bearcat 570 2012













































































Отзывы:

Нет отзывов

Похожие инструкции для Bearcat 570 2012

ski-doo Elite 2004

Бренд: BOMBARDIER Страницы: 14

Ski-Doo MX Z X 440 2004

Бренд: BOMBARDIER Страницы: 16

Ski-Doo Alpine 1977 Series

Бренд: BOMBARDIER Страницы: 24

Бренд: BOMBARDIER Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды