Arctic Cat Bearcat 570 2012 Скачать руководство пользователя

Страница: 8 / 76

General Information

Snowmobile

Identification

The Arctic Cat Snowmobile has two impor-

tant identification numbers. The Vehicle

Identification Number (VIN) is stamped

into the tunnel near the right-side footrest.

The Engine Serial Number (ESN) is

stamped into the crankcase of the engine.

0726-383

These numbers are required by the dealer

to complete warranty claims properly. No

warranty will be allowed by Arctic Cat

Inc. if the engine serial number or VIN is

removed or mutilated in any way.
Always provide the snowmobile name,

VIN, and ESN when contacting an autho-

rized Arctic Cat Snowmobile dealer for

parts, service, accessories, or warranty. If

the complete engine must be replaced,

ask the dealer to notify Arctic Cat for

correct registration information.

Control Locations

Shown are the typical control locations

for Arctic Cat snowmobiles. Location of

a specific control will vary according to

model.

Bearcat 570/570 XT/F570/T570

0744-441

Bearcat Z1 XT/GS

0745-803

Содержание Bearcat 570 2012













































































Результаты поиска

Содержание Bearcat 570 2012

Отзывы:

Похожие инструкции для Bearcat 570 2012

Бренды по названию

Популярные бренды

Arctic Cat Bearcat 570 2012, Руководство оператора

Результаты поиска

Содержание Bearcat 570 2012

Отзывы:

Похожие инструкции для Bearcat 570 2012

Бренды по названию

Популярные бренды