manualshive.com logo in svg

Arctic Cat Bearcat 570 2012, Руководство оператора

Описание продукта: Arctic Cat Bearcat 570 2012. Пользовательский мануал доступен для загрузки бесплатно на manualshive.com. Операторский мануал содержит все необходимые инструкции по эксплуатации данной модели. Необходимо загрузить его, чтобы правильно использовать Arctic Cat Bearcat 570 2012.

Поделиться
Скачать
background image

15

2. Adjust the handlebar up or down and/

or rotate the handlebar to operator’s

desired position; then press down on

the cam lever until it “locks” in place.

Check steering for maximum right/

left turning capabilities.

NOTE: At this point, gently lift the

cam lever without pressing in on the
lock pin. If the cam lever cannot be
lifted, the lock pin is secure.

NOTE: Do not rotate the handlebar

to a position that allows air to enter
the brake system.

3. Test the handlebar to ensure that it

does not rotate within the riser

block. If it does not rotate, proceed

to step 4. If it does rotate, release the

cam lever and rotate the cam lever

clockwise; then press down on the

cam lever until the lock pin is prop-

erly positioned and locked. Repeat

this procedure until the handlebar is

properly secured.

4. After the handlebar is “locked” in

position, release the cam lever and

rotate it one turn clockwise; then

press down on the cam lever until it

“locks” in place.

NOTE: At this point, gently lift the

cam lever without pressing in on the
lock pin. If the cam lever cannot be
lifted, the lock pin is secure.

Exhaust System

The exhaust system is designed to reduce

noise and to improve the total perfor-

mance of the engine. If any exhaust sys-

tem component is removed from the

engine and the engine is run, severe

engine damage will result.

Air-Intake Silencer

Used in conjunction with the fuel intake

system is a specially designed air-intake

silencer. The purpose of the silencer is to

quiet the intake of fresh air. Since the fuel

intake system is calibrated with the air-

intake silencer in place, the engine must

never be run with the silencer removed.

Performance will not be improved if the

air-intake silencer is removed. In con-

trast, severe engine damage will occur.

Cooling System (F5 

LXR/1100 cc Models)

These snowmobiles are equipped with a

closed liquid cooling system for engine

cooling. The cooling system should be

inspected daily for leakage and damage.

Also, the coolant level should be checked

daily. If leakage or damage is detected,

take the snowmobile to an authorized

Arctic Cat Snowmobile dealer for ser-

vice. If not under warranty, this service is

at the discretion and expense of the

snowmobile owner.

Battery

 

(Electric Start)

It is extremely important that the battery

be maintained at full charge at all times

and that the battery connections be clean

and tight. If charging the battery becomes

necessary, refer to Battery sub-section in

the Maintenance section.

CAUTION

If at any time the lock pin will not
engage into the locked position, do
NOT operate the snowmobile. Take
the snowmobile to an authorized Arc-
tic Cat Snowmobile dealer for ser-
vice.

! WARNING

Care must be taken to securely lock
the handlebar cam lever to prevent
unexpected “movement” of the han-
dlebar during operation over rough
terrain. DO NOT position the handle-
bar so steering (maximum right/left
turning capabilities) or throttle and
brake controls are affected.

CAUTION

These snowmobiles are not designed
to be operated in dusty conditions.
Operating the snowmobile in dusty
conditions will result in severe
engine damage.

Содержание Bearcat 570 2012













































































Отзывы:

Нет отзывов

Похожие инструкции для Bearcat 570 2012

Yamaha RS90NL Suplementary Service Manual preview
RS90NL
Бренд: Yamaha Страницы: 308
Yamaha VX600ERG 2001 Service Manual preview
VX600ERG 2001
Бренд: Yamaha Страницы: 282

Бренды по названию

Популярные бренды

Загрузить еще бренды