Arctic Cat Bearcat 570 2012 Скачать руководство пользователя

Страница: 53 / 76

0744-551

6. Install the sheave adjuster and cap

screw onto the driven pulley; then

tighten the cap screw until the mov-

able sheave opens far enough to

allow the belt to be removed.



NOTE: Before installing the drive

belt, use a suitable cleaning solvent
to thoroughly clean the sheaves.

7. Remove the drive belt from the

driven pulley first; then from the

drive clutch.

Installing Drive Belt



NOTE: If a new drive belt is being

installed, see Drive Belt Break-In
sub-section in the General Infor-
mation section.

1. Place the drive belt (so the part num-

ber can be read) between the sheaves

of the drive clutch first; then

between the sheaves of the driven

pulley.

2. Remove the sheave adjuster and install

it in its original position (beveled side

out); then install the cap screw, lock

washer, washer, and sheave adjuster

back into the driven pulley. Tighten the

cap screw to 32 ft-lb.

3. Install the belt guard; then close the

left-side access panel.

4. Release the brake lever lock.

Track Tension

Track tension is directly related to the

overall performance of the snowmobile. If

the track is too loose, it may slap against

the tunnel causing wear or it may “ratchet”

on the track drive sprockets. If extremely

loose, the idler wheels may climb over the

track lugs forcing the track against the tun-

nel causing the track to “lock.” Arctic Cat

recommends that the track tension be

checked daily during the first 300 miles of

operation and once a week thereafter and

adjusted according to need. The track will

stretch and take a “set” during break-in.

Track deflection must be maintained

within the recommended range.

Checking Track Tension

1. Remove excess ice and snow buildup

from the track, track drive sprockets,

and the inside of the skid frame.

2. Elevate the snowmobile on a

shielded safety stand high enough to

use a spring scale.

3. At mid-point of the track (on the bot-

tom side), hook a spring scale around a

track clip; then pull down on the scale

to the recommended pressure. Measure

the deflection (distance) between the

bottom of the wear strip and the inside

surface of the track clip. Compare the

measurement with the chart.

CAUTION

Do not apply Loctite to the driven pul-
ley cap screw or component damage
may occur.

! WARNING

Never operate the snowmobile with-
out the belt guard/access panel
secured in place.

! WARNING

Track tension must be properly main-
tained. Personal injury could result if
a track is allowed to become exces-
sively loose.

! WARNING

DO NOT attempt to check or adjust
track tension with engine running.
Turn ignition key to the OFF position.
Personal injury could result from con-
tact with a rotating track.

Содержание Bearcat 570 2012













































































Результаты поиска

Содержание Bearcat 570 2012

Отзывы:

Похожие инструкции для Bearcat 570 2012

Бренды по названию

Популярные бренды

Arctic Cat Bearcat 570 2012, Руководство оператора

Результаты поиска

Содержание Bearcat 570 2012

Отзывы:

Похожие инструкции для Bearcat 570 2012

Бренды по названию

Популярные бренды