Arctic Cat Bearcat 570 2012 Скачать руководство пользователя

Страница: 14 / 76

Low Oil Warning Icon (570

cc Models)

The Low Oil Warning Icon is designed to

alert the snowmobile operator when the

oil in the oil injection reservoir gets below

a prescribed level; however, it is highly

recommended that a visual verification of

the oil level in the reservoir be done prior

to operating the snowmobile. Once the

Low Oil Warning Icon illuminates during

operation of the snowmobile, the operator

must periodically monitor the level of oil

in the reservoir and must fill the reservoir

the next time gasoline is added to the gas

tank. The “alert level” of the Low Oil

Warning Icon is approximately equal to 1

tankful of gasoline under normal operat-

ing conditions.

Oil Pressure Warning Icon

(Bearcat Z1 XT Models/

TZ1 Model)

The Oil Pressure Warning Icon indicates

engine oil pressure, not the oil level;

however, if the oil level is low, it may

affect oil pressure.
The icon should illuminate each time the

ignition switch is turned to RUN or

START, and it should go out when the

engine starts. If the icon illuminates

while the engine is running, oil pressure

has been lost and the engine will auto-

matically shut off.
If oil pressure is lost, use the following

procedure to check the oil level:

1. With the engine off, remove the

engine oil level stick and wipe it

clean. Without screwing it in, set the

stick back in the oil tank. Remove it

and observe the oil level on the

stick. If the oil level is at or below

the ADD mark on the oil level stick,

add only enough recommended oil

to raise the level to the NORMAL

range. DO NOT overfill the reser-

voir with oil.

2. Open the air bleed bolt located on

the oil pump (beneath the coolant

tank) to purge air from the oil hose.

ZJ004A



NOTE: When air can no longer be

heard purging from oil pump bleed,
tighten the bleed bolt to 7.5 ft-lb.

3. Start the engine. The warning icon

should go out within five seconds.

4. If the warning icon does not go out,

shut the engine off immediately and

repeat step 2; then repeat step 3.

If the warning icon does not go out or if

the engine does not start, take the snow-

mobile to an authorized Arctic Cat Snow-

mobile dealer. If not under warranty, this

service is at the discretion and expense of

the snowmobile owner.

Indicator Icons (Deluxe

Gauge)

Certain models are equipped with a

deluxe gauge combination speedometer/

tachometer. Indicator icons are incorpo-

rated within the speedometer/tachome-

ter. Also incorporated into the

speedometer/tachometer is a digital read-

out screen.

FZ001A

A. High Beam
B. Oil Pressure/Low Oil

CAUTION

Do not attempt to start the engine
with the bleed bolt open.

Содержание Bearcat 570 2012













































































Результаты поиска

Содержание Bearcat 570 2012

Отзывы:

Похожие инструкции для Bearcat 570 2012

Бренды по названию

Популярные бренды

Arctic Cat Bearcat 570 2012, Руководство оператора

Результаты поиска

Содержание Bearcat 570 2012

Отзывы:

Похожие инструкции для Bearcat 570 2012

Бренды по названию

Популярные бренды