APRILIA RX 125 Скачать руководство пользователя страница 33

Страница: 33 / 219

CHECK THE CLUTCH CONTROL CABLE IS IN GOOD CON-
DITIONS: THERE SHOULD BE NO SIGNS OF CRUSHING
OR WEAR ALL ALONG THE SHEATH.

•

Lubricate the clutch wire frequently with an appropriate grease to avoid early wear and cor-

rosion.

See also

Side fairings

Headlight adjustment

NOTE

IN COMPLIANCE WITH LOCAL REGULATIONS IN FORCE, SPECIFIC PROCEDURES MUST BE
FOLLOWED WHEN CHECKING LIGHT BEAM ADJUSTMENT.

For a quick check of the correct adjustment of the

front light beam:

•

Place the vehicle 10 m (32.81 ft) away

from a vertical wall and make sure the

ground is level.

•

Turn on the low-beam light, sit on the

vehicle and check that the light beam

projected to the wall is a little below the

headlight horizontal straight line (about

9/10 of the total height).

To adjust the light beam:

•

Operating on both sides, undo the

screw.

•

Adjust the headlamp until the desired

position is obtained.

•

Working from both sides, tighten the

screw. After adjusting:

NOTE

CHECK THAT THE LIGHT BEAM VERTICAL DIRECTION IS
CORRECT.

RX SX 125

Maintenance

MAIN - 33

Содержание RX 125




























































































































































































































Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды

APRILIA RX 125, Руководство по обслуживанию станции

Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды