APRILIA RX 125 Скачать руководство пользователя страница 189

Страница: 189 / 219

TOTAL

•

Undo and remove both RAVE valve

screws and collect the locking wash-

ers.

•

Take out the exhaust valve unit from

the cylinder.

•

Disconnect the connector of the sys-

tem control unit.

•

Undo and remove both screws (8) from

the battery housing frame.

•

Remove the whole RAVE valve.

Checking

GASKETS

•

Check that the valve gasket (1) and the O-ring (2) (fitted to the valve seat) are not worn or

damaged.

EXHAUST VALVE

•

Clean off any combustion deposits from the exhaust valve (3) and from the valve duct in the

cylinder.

•

Make sure that the exhaust valve is not worn or damaged.

RX SX 125

Chassis

CHAS - 189

Содержание RX 125




























































































































































































































Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды

APRILIA RX 125, Руководство по обслуживанию станции

Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды