APRILIA RX 125 Скачать руководство пользователя страница 157

Страница: 157 / 219

•

Take the pumping member rod fully out

of the sleeve cartridge.

•

Insert the spring keeping the pumping

member rod in place.

•

Insert an open key under the lock nut

to support the pumping member rod

and the spring.

•

Screw the spring until it is fully inserted

into the sleeve end.

•

Place the spring preloading pipe.

•

Screw the upper locking cap on the

pumping member stem.

•

Screw the fork upper cap up to the

pumping member stem.

•

Place the upper cap on the sleeve tak-

ing care not to damage the O-ring.

•

Tighten the upper cap to the prescribed

torque.

RX SX 125

Suspensions

SUSP - 157

Содержание RX 125




























































































































































































































Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды

APRILIA RX 125, Руководство по обслуживанию станции

Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды