APRILIA RX 125 Скачать руководство пользователя страница 116

Страница: 116 / 219

•

Place the extractor plate.

•

Fit the three fixing screws.

•

Adequately centre the plate with refer-

ence to the crankshaft.

•

Tighten the three fixing screws.

•

Screw the long threaded end of the ex-

tractor screw on the extractor plate un-

til the crankcase half on the clutch side

starts to get detached. Facilitate the

detachment of the crankcase by tap-

ping the secondary shaft with a rubber

mallet, being careful that the crank-

case half gets detached evenly. Be ex-

tremely careful not to tap the seal

surfaces.

•

Check the thrust washer of the main

shaft. When detaching the crankcase,

the washer may get glued inside the

crankcase halves.

•

Once the crankcase halves have been

detached, remove the extracting tool

before the crankcase halves are fully

apart.

Specific tooling

AP0277455

Extractor plate to separate the

crankcase halves

Removing the crankshaft

•

Turn the crankcase halves on the sup-

port so that the high ignition is facing

upwards.

Engine

RX SX 125

ENG - 116

Содержание RX 125




























































































































































































































Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды

APRILIA RX 125, Руководство по обслуживанию станции

Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды