APRILIA RX 125 Скачать руководство пользователя страница 55

Страница: 55 / 219

•

Press the MODE switch fast until the

service icon (Wrench symbol) is dis-

played. The words km/h - Mph and OIL

word are displayed first.

•

Hold down the MODE button until the

dashes ---- are displayed. Once the

key is released, the words NO CLEAR

will be displayed.

•

Pressing the MODE switch fast, you

can shift from NO to YES and vice ver-

sa.

•

If YES CLEAR is displayed, press the

MODE switch and hold it for more than

three seconds to reset the service icon

(Wrench symbol).

•

To exit turn the key to OFF.

CAUTION

IF A SCREEN DIFFERENT FROM THOSE DESCRIBED IS
DISPLAYED, EXIT BY TURNING THE KEY TO OFF.

RX SX 125

Electrical system

ELE SYS - 55

Содержание RX 125




























































































































































































































Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды

APRILIA RX 125, Руководство по обслуживанию станции

Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды