APRILIA RX 125 Скачать руководство пользователя страница 187

Страница: 187 / 219

The solenoid controlled by the rave control unit opens the exhaust valve at 8000 rpm.

TROUBLESHOOTING

•

Check that the 7.5 A fuse is in good

conditions.

•

Check the if the solenoid is working

properly by powering it directly with a

12 V battery.

•

Check the flywheel

•

Replace the regulator with another one

in proper operating conditions.

•

Replace the EFI control unit with an-

other one in proper operating condi-

tions.

CAUTION

THE RAVE VALVE CHECKING FUNCTION IS ACTIVATED
WHEN THE EFI CONTROL UNIT JUMPER IS CUT OFF.

SOLENOID

•

Check that the piston moves freely.

•

Measure the resistance between the wires with a tester:

•

Correct value = 2.2 Ohm + / - 10%.

•

Start the vehicle, go over 6500 rpm

•

Let the engine idling

RX SX 125

Chassis

CHAS - 187

Содержание RX 125




























































































































































































































Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды

APRILIA RX 125, Руководство по обслуживанию станции

Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды