APRILIA RX 125 Скачать руководство пользователя страница 165

Страница: 165 / 219

Insert the anti-vibration buffer in the wheel hub.

Fit the entire final transmission unit on the wheel, manually rotate the crown gear to right and left and

check the clearance between the anti-vibration buffer and the hub. Replace the anti-vibration buffer if

excessive clearance is found.

CROWN GEAR

Check the toothing of the crown and the pinion. If excessive wear is found, replace: the crown, the pinion

and the drive chain.

CAUTION

REPLACE ALL THREE PARTS TO PREVENT EARLY WEAR OF NEW COMPONENTS.

Installing the rear wheel

•

Position the rear wheel.

•

Position the chain.

•

Working on both sides, insert the centring shim washers.

•

Working from the left side, insert the wheel axle.

CAUTION

DO NOT INVERT THE RIGHT AND THE LEFT CHAIN TENSIONERS.

•

Working on the right side, position the washer and screw but do not tighten the wheel axle

fixing nut.

•

Adjust the chain tension operating the set screws.

CAUTION

AFTER REFITTING, OPERATE THE REAR BRAKE LEVER REPEATEDLY AND CHECK THAT THE
BRAKING SYSTEM OPERATES CORRECTLY.

CAUTION

CHECK THAT THE WHEEL IS CENTRED.

•

Tighten the wheel axle fixing nut.

See also

Adjusting

RX SX 125

Suspensions

SUSP - 165

Содержание RX 125




























































































































































































































Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды

APRILIA RX 125, Руководство по обслуживанию станции

Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды