APRILIA RX 125 Скачать руководство пользователя страница 94

Страница: 94 / 219

Starter motor

STARTER MOTOR

•

Make sure that the toothing (1) is not

deformed or worn.

•

Make sure that the O-ring (2) is not

damaged or worn.

•

The electric starter motor is not fitted

for repair. If necessary, replace the

whole motor.

START-UP GEAR

•

Make sure that the gears (3) are not

worn.

•

The start-up gears must be blocked

with precision in one direction.

Removing the starter motor

•

Undo and remove the two fixing screws.

•

Remove the starter motor.

NOTE

THE STARTER MOTOR CAN ALSO BE REMOVED IF THE ENGINE IS FITTED TO THE VEHICLE.

Installing the starter motor

•

Place the electric starter motor.

•

Apply LOCTITE 221.

•

Tighten the starter motor fixing screws.

Engine

RX SX 125

ENG - 94

Содержание RX 125




























































































































































































































Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды

APRILIA RX 125, Руководство по обслуживанию станции

Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды