APRILIA RX 125 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 219

background image

•

Grip the two connectors and disconnect them by pulling them in opposite directions.

•

If any signs of dirt, rust, moisture, etc. are noted, clean the inside of the connector carefully

with a jet of compressed air.

•

Ensure that the cables are correctly fastened to the internal connector terminals.

•

Then connect the two connectors, ensuring that they couple correctly (if fitted with clips, you

will hear them "click" into place).

CAUTION

DO NOT DISCONNECT CONNECTORS BY PULLING THE CABLES.

NOTE

THE TWO CONNECTORS CAN ONLY BE CONNECTED IN ONE DIRECTION: CONNECT THEM
THE RIGHT WAY ROUND.

TIGHTENING TORQUES

CAUTION

REMEMBER THAT THE TIGHTENING TORQUES FOR ALL FASTENING ELEMENTS ON WHEELS,
BRAKES, WHEEL AXLES AND ANY OTHER SUSPENSION COMPONENTS PLAY A KEY ROLE
IN ENSURING VEHICLE SAFETY AND MUST COMPLY WITH SPECIFIED VALUES. CHECK THE
TIGHTENING TORQUES OF FASTENING ELEMENTS ON A REGULAR BASIS AND ALWAYS USE
A TORQUE WRENCH TO REASSEMBLE THESE COMPONENTS. FAILURE TO COMPLY WITH
THESE RECOMMENDATIONS MAY CAUSE ONE OF THESE COMPONENTS TO LOOSEN OR
EVEN DETACH, CAUSING A WHEEL TO LOCK OR COMPROMISING VEHICLE HANDLING. THIS
MAY LEAD TO FALLS, WITH THE RISK OF SERIOUS INJURY OR DEATH.

Running-in

Engine run-in is essential to ensure engine long life and correct operation. Twisty roads and gradients

are ideal to run in engine, brakes and suspensions effectively. Vary your riding speed during the run-

in. This ensures that components operate under both "loaded" and "unloaded" conditions, allowing the

engine components to cool.

CAUTION

THE FULL PERFORMANCE OF THE VEHICLE IS ONLY AVAILABLE AFTER THE SERVICE AT
THE END OF THE RUN-IN PERIOD.

Follow the guidelines detailed below:

•

Do not twist the throttle grip abruptly and completely when the engine is working at a low

revs, either during or after run-in.

•

During the first 100 km (62 miles) brake carefully to avoid rough and long braking. That is

to permit the adequate adjustment of the pad friction material to the brake discs.

Vehicle identification

CAUTION

CHANGING THE IDENTIFICATION CODE IS A CRIME THAT MAY BE PUNISHED WITH SERIOUS
CRIMINAL CHARGES. FURTHERMORE, THE LIMITED WARRANTY FOR NEW VEHICLES WILL
BE CANCELLED IF THE VEHICLE IDENTIFICATION NUMBER (VIN) HAS BEEN MODIFIED OR
CANNOT BE QUICKLY DETERMINED.

Characteristics

RX SX 125

CHAR - 10

«
...
8
9
10
11
12
...
»

Содержание RX 125




























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RX 125

Бренд: X-lite Страницы: 6

Бренд: Yamaha Страницы: 572

Бренд: Yamaha Страницы: 584

Бренд: Yamaha Страницы: 410

Бренд: Yamaha Страницы: 576

Бренд: Yamaha Страницы: 668

Бренд: Yamaha Страницы: 596

Бренд: Yamaha Страницы: 656

Бренд: Yamaha Страницы: 378

Бренд: Memphis Shades Страницы: 2

Бренд: Fantic Motor Страницы: 145

Бренд: Christopeit Sport Страницы: 16

Бренд: R&G Страницы: 2

Бренд: R&G Страницы: 27

Бренд: hepco & becker Страницы: 3

Бренд: Shark Страницы: 44

DARK SMOKE SPORT

Бренд: Malossi Страницы: 4

Бренд: SpeedAngle Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды