APRILIA RX 125 Скачать руководство пользователя страница 118

Страница: 118 / 219

•

Check that all ball bearings move smoothly and are not worn. When replacing the ball bear-

ings, check the negative allowance in the crankcase. Min. ALLOWANCE = 0.010 mm

(0.00039 in).

ONLY THE BALL BEARING SEATS OF THE DESMODROMIC DRUM ARE SLIDING.

•

Make sure that all the seal surfaces are proper conditions and not damaged.

•

Check that all threads are in proper conditions.

FLYWHEEL SIDE CRANKCASE HALF

•

Pre-warm the crankcase half at ap-

prox. 60 - 100 °C (140 - 212 °F).

•

Remove both reference pins (1).

PLACE THE CRANKCASE HALF ON A SUITABLE LEVEL
SURFACE TO AVOID DAMAGING THE SEAL SURFACES.

FLYWHEEL SIDE CRANKCASE HALF

•

Take out the oil seal (2) and the ball

bearing (3) of the crankshaft with a suit-

able punch (4).

BEHIND THE BALL BEARING THERE ARE SOME SHIM
WASHERS FOR THE AXIAL CLEARANCE OF THE CRANK-
SHAFT (5).
ALSO REPLACE THE OIL SEAL IF THE BALL BEARING IS
REPLACED.

•

Fit the oil seal of the crankshaft using

a punch (6).

THE BALL BEARING OF THE CRANKSHAFT (3) IS FITTED
TOGETHER WITH THE CRANKSHAFT AFTER CHECKING
THE AXIAL CLEARANCE.

Specific tooling

AP0277875

Buffer for fitting oil seal 230425

•

First remove the oil seal (8) and then take out the ball bearing (7) of the main shaft with a

suitable punch.

DO NOT DAMAGE THE OIL SEAL HOUSING WHEN REMOVING THE SEAL.

Engine

RX SX 125

ENG - 118

Содержание RX 125




























































































































































































































Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды

APRILIA RX 125, Руководство по обслуживанию станции

Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды