APRILIA RX 125 Скачать руководство пользователя страница 92 | Manualshive

Страница: 92 / 219

background image

•

The lever roller (6) must rotate freely.

•

Check that the stop tab (7) and the rel-

evant spring (8) work properly.

•

Check that the gear shaft is not de-

formed. (A) Max. admissible deviation

= 0.15 mm (0.0059 in);

•

Check that both fork shafts are not de-

formed. (B) Max. admissible deviation

= 0.05 mm (0.0020 in);

THE END OF THE FORK LONG SHAFT (9) THAT PRO-
TRUDES FROM THE CRANKCASE IS USED AS A TRANS-
MISSION STOP AND CAN BE BENT IN CASE OF EXCES-
SIVE LOAD (BUMPING).
THE DEVIATION CAN BE CHECKED BY REMOVING THE
CLUTCH COVER AND ROTATING THE LONG SHAFT.

Assembling the gearbox

•

Place the guiding sleeve on the pri-

mary shaft to avoid damaging the oil

seal.

•

Heat up the engine crankcase.

•

Apply LOCTITE Anti-Seize on the

bearing seats present on the crank-

case.

•

Fit the bearings in their seats.

•

Fit the gear unit.

•

Fit the 5th - 6th gear fork on the gear

pinion of the secondary shaft.

•

Place the 2nd - 3rd gear fork and the

1st - 4th gear fork on the gear pinion of

the primary shaft. The 2nd - 3rd gear

fork must be installed with the printed

number 123 facing upwards. The 1st -

4th gear fork must be installed with the

printed number 113 facing upwards.

Engine

RX SX 125

ENG - 92

«
...
90
91
92
93
94
...
»

Содержание RX 125




























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RX 125

Бренд: MadStad Engineering Страницы: 2

Бренд: HYOSUNG Страницы: 98

Бренд: Suzuki Страницы: 206

Бренд: Dakota Digital Страницы: 6

Бренд: SUOMY Страницы: 84

B40 VICTOR W D 1967

Бренд: BSA Страницы: 128

Бренд: SHOEI Страницы: 38

Daytona 675 2014

Бренд: Triumph Страницы: 162

Бренд: LAS Страницы: 22

Бренд: DYNATEK Страницы: 4

Бренд: hepco & becker Страницы: 2

Бренд: hepco & becker Страницы: 4

Бренд: hepco & becker Страницы: 6

VarioProtect XXL-W-2 TC

Бренд: Schweißkraft Страницы: 16

Бренд: Cagiva Страницы: 142

Бренд: Benelli Страницы: 454

Бренд: Tecnico Страницы: 182

Бренд: KTM Страницы: 118

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды