APRILIA RX 125 Скачать руководство пользователя страница 156

Страница: 156 / 219

•

Place the stem cover guide in the

sleeve and tighten the fixing screw.

Filling oil

•

Place the sleeve upright in a vice fitted

with protection jaws.

•

Compress the sleeve in the stem.

Place a support under the stem in order

to leave it compressed.

•

Pour part of the fork oil into the sleeve.

•

Wait some minutes until the oil fills all

the ducts.

•

Pour the remaining oil.

•

Pump out oil a few times.

•

Measure the air gap between the oil

level and the rim.

THE SLEEVE MUST BE PERFECTLY UPRIGHT IN ORDER
TO MEASURE THE CORRECT OIL LEVEL. THE OIL LEVEL
MUST BE THE SAME IN BOTH STEMS.

Characteristic

Oil level (from sleeve rim, without the spring
and with stem at the end of the stroke)

150 mm (5.9 in)

•

Slowly move the cartridge upwards

and downwards rod so that it is filled

with oil.

•

Do so until, pulling it upwards, there is

a noticeable uniform resistance

throughout the whole stroke.

•

Tighten the lock nut until it reaches the

pumping member stem.

Suspensions

RX SX 125

SUSP - 156

Содержание RX 125




























































































































































































































Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды

APRILIA RX 125, Руководство по обслуживанию станции

Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды