APRILIA RX 125 Скачать руководство пользователя страница 17

Страница: 17 / 219

Name

Torque in Nm

Instrument panel support / tank to upper plate retainer - TCEI

M6x30 screw (1)

10 Nm (7.37 lbf ft)

Tank cover to chassis retainer - TE M6x30 screw (1)

10 Nm (7.37 lbf ft)

Tank cover to tank retainer - TBEI M5 screw (2)

5 Nm (3.69 lbf ft)

Rh/ Lh deflector brackets to radiator system retainer - TBEI

M5x9 screw (2)

5 Nm (3.69 lbf ft)

Rh/ Lh deflector bracket to radiator systems retainer - TCB

M4x16 screw (2)

3 Nm (2.21 lbf ft)

Rh/ Lh deflector to chassis retainer - TBEI M5x9 (2) screw

5 Nm (3.69 lbf ft)

Rh/ Lh deflector to tank front retainer - TE M5x25 (2) screw

5 Nm (3.69 lbf ft)

Rh/ Lh chassis cover retainer - TBEI M5x12 (2) screw

5 Nm (3.69 lbf ft)

INISHINGS

Name

Torque in Nm

Saddle lock tongue retainer - screw (1)

3 Nm (2.21 lbf ft)

Switch retainer - TCEI M8x16 screw (1)

25 Nm (18.44 lbf ft)

Switch - shear head screw retainer (1)

Manual

Recommended products chart

LUBRICANTS CHART

Product

Description

Specifications

Agip GEAR SYNTH, SAE 75W - 90

Gearbox oil

As an alternative for recommended oils,

use top branded oils that meet or exceed

the API GL - 4 requirements.

AGIP FORK 7.5W

Recommended FORK OIL

If you intend to have an intermediate per-
formance, as an alternative to the recom-
mended AGIP FORK 5W or AGIP FORK

20W use:

AGIP FORK 7.5W

AGIP FORK 10W
AGIP FORK 15W

AGIP SPEED 2T

Mixer oil

As an alternative for recommended oils,

use top branded fully synthetic oils that

meet or exceed the ISO - L - EGD, JASO

FC or API TC specifications require-

ments.

AGIP GREASE SM 2

Grease for C-ring of the tone wheel

Soap-based lithium grease with NLGI 2

molybdenum disulphide; ISO-L-

XBCHB2, DIN KF2K-20

NEUTRAL GREASE OR PETROLEUM

JELLY

Battery poles

Neutral grease or petroleum jelly.

AGIP CHAIN GREASE SPRAY

Chain spray grease

AGIP BRAKE 4 / BRAKE 5.1

Recommended BRAKE FLUID

RX SX 125

Characteristics

CHAR - 17

Содержание RX 125




























































































































































































































Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды

APRILIA RX 125, Руководство по обслуживанию станции

Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды