APRILIA RX 125 Скачать руководство пользователя страница 137 | Manualshive

Страница: 137 / 219

background image

Engine parameter screen page

ENGINE PARAMETER READING

Specification

Desc./Quantity

Engine revs

rpm, measured with crankshaft rpm detection sensor

Throttle valve opening

%, indication ranges from 0 to 100 %

Air temperature

23 °C, if signal is lost, the control unit set the value to 50 °C

Battery voltage

12 V

Ignition advance

12 °, ignition advance with respect to TDC

Warm - up time (from KEY ON)

s

Vehicle speed

0 km / h

Devices activation screen page

DEVICE ACTIVATION

Specification

Desc./Quantity

Deleting errors

By pressing the 'enter' button, the stored errors (MEM) become

part of the historical data (STO). The next time Axone is con-

nected to the ECU, the errors in the historical record (STO) will

no longer be displayed

Coil

The coil is activated five times

Outlet valve

The solenoid valve is activated five times

Intake air solenoid valve

The solenoid valve is activated five times

Rpm indicator

The needle should be at 10000 rpm for two seconds

Speed gauge

Activates the speedometer at 100 km / h

Errors display screen page

CAUTION

IF THERE IS ANY ENGINE FAILURE, THE CONTROL UNIT DOES NOT TURN ON THE EFI WARN-
ING LIGHT.
THE EFI WARNING LIGHT IS INACTIVE IN THIS VEHICLE.
THE OPERATOR WHO ENCOUNTERS A FAILURE IN THE ENGINE MUST CARRY OUT ALL THE
PRESCRIBED AXONE CHECKS WITH THE AIM OF ENSURING THE ENGINE HAS BEEN THOR-
OUGHLY CHECKED.

ERRORS DISPLAY

Specification

Desc./Quantity

EEPROM : checksum error. Signal not valid

Control unit internal error

Data zone EEPROM not valid : default values reset

Control unit internal error

Crankshaft position sensor Circuit open

An interruption has been detected between pin 9 and pin 3 of

the small connector in the control unit

Crankshaft position sensor Shorted to ground

Continuity has been detected between the ground connection

and pin 9

Crankshaft position sensor Signal not valid

Abnormal voltage has been detected due to an electric resist-

ance not foreseen in the circuit connecting to the revolution

sensor: between pin 9 and pin 3 of the small connector of the

control unit

Ignition capacitor Shorted to ground

Error detected in the capacitor charging system in the control

unit: check that the power supply and ground connection of the

control unit are adequate

Ignition coil (circuit open)

Lack of ground connection to pin 14 has been detected

No ignition

Error detected in the capacitor charging system in the control

unit: check that the power supply and ground connection of the

control unit are adequate

No ignition

Error detected in the capacitor charging system in the control

unit: check that the power supply and ground connection of the

control unit are adequate

Incorrect crankshaft signal. Signal not valid

Abnormal error detected by the control unit

RX SX 125

Power supply

P SUPP - 137

«
...
135
136
137
138
139
...
»

Содержание RX 125




























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RX 125

Бренд: Cannondale Страницы: 102

Бренд: KAYO MOTOR Страницы: 74

Бренд: KAYO MOTO Страницы: 5

V 7 CAFE CLASSIC

Бренд: MOTO GUZZI Страницы: 147

Бренд: IRC Страницы: 2

990D0-31J50-CLE

Бренд: Suzuki Страницы: 12

Dirt rocket XM500

Бренд: X-TREME scooter Страницы: 14

Бренд: MOTO GUZZI Страницы: 134

Бренд: Sundstrom Страницы: 68

Бренд: R&G Страницы: 4

Бренд: R&G Страницы: 4

TuneUp H33-M24-L15

Бренд: Ear Defender Страницы: 64

Бренд: Razor Страницы: 16

Бренд: Power Fist Страницы: 4

Бренд: SILENCE Страницы: 68

Бренд: TGB Страницы: 219

Бренд: MZ Страницы: 204

Бренд: Yamaha Страницы: 98

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды