APRILIA RX 125 Скачать руководство пользователя страница 106

Страница: 106 / 219

•

The seal surface of the combustion

chamber insert gets slightly conic start-

ing from a 63 mm (2.48 in) diameter.

CYLINDER HEAD COVER

•

Make sure the seal surfaces of the two

O-rings are clean.

•

Make sure the cylinder head cover is

not damaged.

Cylinder-piston assembly

Removing the cylinder

•

Remove the head.

•

Working from both sides remove the

four fixing screws and collect the wash-

ers.

•

Take out the cylinder with utmost care

trying not to damage the piston.

•

Remove the gasket on the cylinder

base.

See also

Removing the cylinder head

Engine

RX SX 125

ENG - 106

Содержание RX 125




























































































































































































































Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды

APRILIA RX 125, Руководство по обслуживанию станции

Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды