APRILIA RX 125 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 219

background image

•

Screw the filler plug (1).

•

Start the engine and let it idle for about a minute to allow the gearbox oil circuit to get filled.

•

Check the oil level and refill if necessary.

TIGHTEN UP THE FILLER CAP AND MAKE SURE THE OIL DOES NOT SEEP.
CHECK REGULARLY THAT THERE ARE NO LEAKS IN THE CRANKCASE COVER GASKET.
DO NOT RIDE THE VEHICLE WITH INSUFFICIENT LUBRICATION OR WITH CONTAMINATED OR
INCORRECT LUBRICANTS AS THIS ACCELERATES THE WEAR AND TEAR OF THE MOVING
PARTS AND CAN CAUSE IRRETRIEVABLE DAMAGE.

Air filter

•

Remove the right side central fairing.

•

Undo and remove the 4 screws and re-

move the filter casing side cover.

•

Remove the filtering element together

with the mesh.

•

Wash the filtering element with clean,

non-flammable or high-volatility sol-

vents, and let it dry properly.

•

Apply filter oil or heavy oil (SAE 80W -

90) all over the whole surface and then

wring the filtering element to eliminate

excess oil.

THE FILTERING ELEMENT MUST BE WELL IMPREGNA-
TED BUT SHOULD NOT DRIP.

•

Clean the air filter more frequently if the vehicle is used on dusty or wet roads.

•

In this case, the air filter can be partially cleaned after such a ride.

AIR FILTER PARTIAL CLEANING DOES NOT EXCLUDE OR POSTPONE REPLACING THE FIL-
TER.

Maintenance

RX SX 125

MAIN - 28

«
...
26
27
28
29
30
...
»

Содержание RX 125




























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RX 125

Бренд: hepco & becker Страницы: 6

Бренд: BMW Страницы: 176

Бренд: SSR Motorsports Страницы: 39

ZTechnik VStream Z2392

Бренд: National Cycle Страницы: 2

Бренд: KTM Power Parts Страницы: 7

Бренд: R&G Страницы: 6

Бренд: Clas Ohlson Страницы: 5

Бренд: Saddlemen Страницы: 6

Multistrada 1200 ABS

Бренд: Ducati Страницы: 199

PANIGALE V4 2022

Бренд: Ducati Страницы: 310

Бренд: Ducati Страницы: 273

Бренд: Buell Страницы: 9

Super Meteor 650

Бренд: Royal Enfield Страницы: 124

Бренд: Kinroad Страницы: 25

Бренд: Kemimoto Страницы: 3

Бренд: APRILIA Страницы: 128

Бренд: APRILIA Страницы: 162

Бренд: hepco & becker Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды