APRILIA RX 125 Скачать руководство пользователя страница 196

Страница: 196 / 219

•

Remove the water pump with the help

of a square screwdriver.

REFITTING

•

Upon refitting follow the removal steps but in reverse order, paying special attention to the

alignment of the water pump control wheel, which must be aligned with the reference on the

crankcase when refitting.

Removing the radiator

•

Remove both front side fairings.

•

Place a container of suitable capacity

underneath the sleeve.

•

Release the clamp.

•

Slide off the sleeve.

•

Empty the liquid into the container.

•

Open the radiator cap to facilitate

drainage.

Cooling system

RX SX 125

COOL SYS - 196

Содержание RX 125




























































































































































































































Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды

APRILIA RX 125, Руководство по обслуживанию станции

Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды