APRILIA RX 125 Скачать руководство пользователя страница 212

Страница: 212 / 219

•

Tighten the bleed screw again and fill

the reservoir until the oil reaches the

recommended level.

Battery

BATTERY REMOVAL

•

Remove the saddle.

•

Make sure the ignition switch is set to

«OFF».

•

Disconnect the negative ( -) lead first

and then the positive (red) (+) one.

•

Remove the battery breather pipe.

•

Remove the battery from its housing

and put it away on a level surface in a

cool and dry place.

CAUTION

ONCE REMOVED, THE BATTERY MUST BE PUT AWAY IN
A SAFE PLACE OUT OF THE REACH OF CHILDREN.

Tail guard

•

Remove the saddle and the central

side fairings.

•

Undo and remove the two screws.

•

Undo and remove the two lower

screws.

Bodywork

RX SX 125

BODYW - 212

Содержание RX 125




























































































































































































































Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды

APRILIA RX 125, Руководство по обслуживанию станции

Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды