APRILIA RX 125 Скачать руководство пользователя страница 79

Страница: 79 / 219

•

Insert the front screw that fixes the en-

gine to the chassis and fasten the nut.

•

Place the swingarm on the chassis.

•

Move it into position so that the holes

are aligned and, at the same time, in-

sert the pin fully from the left side.

•

The correct adjustment of the swing-

arm pin clearance is obtained by prop-

erly seating the ring nut set bushing (1)

and screwing it another 1 / 4 of a turn.

CAUTION

GET THE ADEQUATE SWINGARM PIN ADJUSTMENT
TOOL.

Specific tooling

AP8101945

Fork pin ring nut

•

Firmly hold the bushing (2) and tighten the ring nut (1) using a special tool.

•

Now adjust the rear swingarm pin as follows:

- Using the adequate adjustment tool loosen the ring nut (1) completely working from the upper right

side.

- Tighten the ring nut set bushing (2) to the prescribed torque.

RX SX 125

Engine from vehicle

ENG VE - 79

Содержание RX 125




























































































































































































































Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды

APRILIA RX 125, Руководство по обслуживанию станции

Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды