APRILIA RX 125 Скачать руководство пользователя страница 105

Страница: 105 / 219

Removing the head cover

•

Undo and remove the four Allen

screws fixing the head cover.

•

Remove the head cover.

•

Remove both O-rings.

Removing the cylinder head

•

Remove the head cover.

•

Remove the five M8 Allen screws and

the locking washers.

•

Remove the combustion chamber in-

sert together with the O-Ring.

See also

Removing the head cover

Cylinder head

Checking the cylinder head

HEAD

•

Clean off any combustion deposits in

the combustion chamber as well as

scales on the surfaces in contact with

the cooling water.

•

Make sure the insert in the combustion

chamber is not damaged and the spark

plug thread is in good conditions.

•

Make sure the seal surfaces are

smooth and not damaged.

RX SX 125

Engine

ENG - 105

Содержание RX 125




























































































































































































































Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды

APRILIA RX 125, Руководство по обслуживанию станции

Результаты поиска

Содержание RX 125

Отзывы:

Похожие инструкции для RX 125

Бренды по названию

Популярные бренды