Engineering manual
77
1.6 Installation
1.6.1 Installation accessories
Optional accessories:
Name Used
for
Panel 625
×
625
Gird ceiling installation
Panel 725
×
725 Hard
ceiling
installation
1.6.2 Select the best location
While selecting a place for the indoor unit:
1. Allow max. air flow to the desire space
2. Allow max return air flow
3. Ensure adequate drainage of condensed water
4. Ensure noise reduction near bedrooms
5. Leave a minimum 250 mm free space in front of the filter
6. Allow a free service access to electrical box
7. Allow easy access to the base of the indoor unit while providing enough space from the ceiling
8. Use serrated rubber under the unit and flexible joints to avoid resonance vibrations
Notice:
1. Do not install the cassette in a room where gasses, acids or inflammable products are stored, in order to avoid damage
to the aluminium and copper evaporators and the internal plastic parts.
2. Do not install the cassette in a workshop or a kitchen. Oil vapour attracted by the treated air could form deposits on the
cassette evaporators and modify their performance or damage the cassette's internal plastic parts.
3. Do not install the cassette in a laundry, or a room where steam is produced.
4. The appliance must be positioned so that the plug is accessible.
Содержание KXV Series
