Agilent Technologies U1840A Medalist sj5000 Скачать руководство пользователя страница 44

Страница: 44 / 192

3-6

Agilent U1840A Medalist sj5000 Hardware Manual

Installation

Adjusting the Height and Leveling the sj5000

Adjusting the Height

The four adjustable feet are used to vary the height of the
sj5000. As described in

“Moving the sj5000”

, the height must be

adjusted so that the system conveyor height matches that of the
input and output conveyors.

Leveling the sj5000

After adjusting the height, level the machine as follows:

Loosen the feet locking nuts.

Place the level gauge on the X rail and adjust the feet until
the machine is level.

Do the same way for the Y rail.

Ensure the final height is same as the input and output
conveyors.

Once the correct level has been achieved, tighten the feet
locking nuts.

Содержание U1840A Medalist sj5000

































































































































































































Результаты поиска

Содержание U1840A Medalist sj5000

Отзывы:

Похожие инструкции для U1840A Medalist sj5000

Бренды по названию

Популярные бренды

Agilent Technologies U1840A Medalist sj5000, Руководство по оборудованию

Результаты поиска

Содержание U1840A Medalist sj5000

Отзывы:

Похожие инструкции для U1840A Medalist sj5000

Бренды по названию

Популярные бренды