Agilent Technologies U1840A Medalist sj5000 Скачать руководство пользователя страница 141 | Manualshive

Страница: 141 / 192

background image

Troubleshooting

11

Agilent U1840A Medalist sj5000 Hardware Manual

11-7

Troubleshooting the Conveyor

•

Conveyor will not load a board

•

Board passes straight through the machine and will not stop
for inspection

•

In-Position sensor sensitivity

•

Failed boards will not exit the system

•

Conveyor belt(s) reverse direction unexpectedly

•

Clamp motor continuously rotates

•

Board is not clamped

•

Inspection yields fiducial mis-reads

•

Conveyor will not run

•

Conveyor 1 will not run

•

Conveyor will not run because there is no output from PLC

•

Drives will not move/home/move to a given width

•

Cannot manually adjust the width of the conveyor rail

•

Conveyor rails will not align properly

Conveyor will not load a board

•

The SMEMA cable may not connected. Check the connection
at the upstream conveyor and the back of the sj5000.

•

The sj5000 may believe there is a board already present.
Check that all three sensors are not flagged by either a board
or gantry. All sensors have sensitivity potentiometers that
may be set too sensitive and are identifying the rail or other
hardware as a board. This can be verified by reviewing the
input PLC modules.

Board passes straight through the machine and will not stop for

inspection

•

The sj5000 is in pass through mode. Check the

RAIL

switch(es) on the switch plate and ensure it is set to

INSP

(inspect).

•

The In-Position sensor is not being flagged as the board
passes through the sj5000. This can be verified at the PLC
module or by manually flagging the position sensor.

«
...
139
140
141
142
143
...
»

Содержание U1840A Medalist sj5000

































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для U1840A Medalist sj5000

Бренд: B&K Страницы: 5

Бренд: B&K Страницы: 28

Бренд: Keithley Страницы: 36

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: Kapriol Страницы: 32

Бренд: JABO Страницы: 4

Бренд: GE Страницы: 802

Бренд: iET Страницы: 17

Бренд: Yamaha Страницы: 50

Бренд: A&D Страницы: 30

Бренд: vanEE Страницы: 52

Бренд: Caddon Hives Страницы: 3

Бренд: Nektar Страницы: 3

Бренд: Youkey Страницы: 86

Бренд: Garmin Страницы: 2

Бренд: Garmin Страницы: 12

Бренд: Garmin Страницы: 13

Бренд: Nel-Tech Labs Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды